Make LUFA stack as default for ADB converter

1 files changed, 88 insertions, 20 deletions

diff --git a/converter/adb_usb/Makefile b/converter/adb_usb/Makefile
index 09f30180a8..372ef6c09a 100644
--- a/converter/adb_usb/Makefile
+++ b/converter/adb_usb/Makefile
@@ -1,5 +1,45 @@
+#----------------------------------------------------------------------------
+# On command line:
+#
+# make all = Make software.
+#
+# make clean = Clean out built project files.
+#
+# make coff = Convert ELF to AVR COFF.
+#
+# make extcoff = Convert ELF to AVR Extended COFF.
+#
+# make program = Download the hex file to the device.
+#                Please customize your programmer settings(PROGRAM_CMD)
+#
+# make teensy = Download the hex file to the device, using teensy_loader_cli.
+#               (must have teensy_loader_cli installed).
+#
+# make dfu = Download the hex file to the device, using dfu-programmer (must
+#            have dfu-programmer installed).
+#
+# make flip = Download the hex file to the device, using Atmel FLIP (must
+#             have Atmel FLIP installed).
+#
+# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
+#               (must have dfu-programmer installed).
+#
+# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
+#                (must have Atmel FLIP installed).
+#
+# make debug = Start either simulavr or avarice as specified for debugging, 
+#              with avr-gdb or avr-insight as the front end for debugging.
+#
+# make filename.s = Just compile filename.c into the assembler code only.
+#
+# make filename.i = Create a preprocessed source file for use in submitting
+#                   bug reports to the GCC project.
+#
+# To rebuild project do "make clean" then "make all".
+#----------------------------------------------------------------------------
+
 # Target file name (without extension).
-TARGET = adb_usb
+TARGET = adb_usb_lufa
 
 # Directory common source filess exist
 TOP_DIR = ../..
@@ -7,7 +47,7 @@ TOP_DIR = ../..
 # Directory keyboard dependent files exist
 TARGET_DIR = .
 
-# keyboard dependent files
+# project specific files
 SRC =	keymap.c \
 	matrix.c \
 	led.c \
@@ -16,22 +56,47 @@ SRC =	keymap.c \
 CONFIG_H = config.h
 
 
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
-
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
 
 # Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
 F_CPU = 16000000
 
 
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
 # Boot Section Size in *bytes*
 #   Teensy halfKay   512
 #   Teensy++ halfKay 1024
@@ -44,20 +109,23 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096
 # Build Options
 #   comment out to disable the options.
 #
-#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-#MOUSEKEY_ENABLE = yes	# Mouse keys(+5000)
-#EXTRAKEY_ENABLE = yes	# Audio control and System control(+600)
-#CONSOLE_ENABLE = yes    # Console for debug
-#COMMAND_ENABLE = yes    # Commands for debug and configuration
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
 #SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes	# USB Nkey Rollover(+500)
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+
 
+# Optimize size but this may cause error "relocation truncated to fit"
+#EXTRALDFLAGS = -Wl,--relax
 
 # Search Path
 VPATH += $(TARGET_DIR)
 VPATH += $(TOP_DIR)
 
-include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/protocol/lufa.mk
 include $(TOP_DIR)/protocol.mk
 include $(TOP_DIR)/common.mk
 include $(TOP_DIR)/rules.mk