hhkb: Integrate RN-42 support, remove hhkb_rn42

1 files changed, 103 insertions, 0 deletions

diff --git a/keyboard/hhkb/not_supported/Makefile.iwrap b/keyboard/hhkb/not_supported/Makefile.iwrap
new file mode 100644
index 0000000000..2d9d82c481
--- /dev/null
+++ b/keyboard/hhkb/not_supported/Makefile.iwrap
@@ -0,0 +1,103 @@
+#
+# Makefile for iWRAP
+#
+
+
+# Target file name (without extension).
+TARGET = hhkb_iwrap
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =	\
+	keymap.c \
+	matrix.c \
+	led.c
+
+CONFIG_H = config_iwrap.h
+
+
+# V-USB debug level: To use ps2_usart.c level must be 0
+# ps2_usart.c requires USART to receive PS/2 signal.
+OPT_DEFS = -DDEBUG_LEVEL=0
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+MCU = atmega328p
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 12000000
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=2048
+
+
+# Build Options
+#   comment out to disable the options.
+#
+BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration
+MOUSEKEY_ENABLE = yes	# Mouse keys
+EXTRAKEY_ENABLE = yes	# Audio control and System control
+CONSOLE_ENABLE = yes	# Console for debug
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#NKRO_ENABLE = yes	# USB Nkey Rollover
+
+
+
+#---------------- Programming Options --------------------------
+AVRDUDE = avrdude
+# Type: avrdude -c ? to get a full listing.
+AVRDUDE_PROGRAMMER = usbasp
+AVRDUDE_PORT =
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level.  Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+include $(TOP_DIR)/protocol/iwrap.mk
+# TODO: to be selectable: V-USB, LUFA or PJRC
+#include $(TOP_DIR)/protocol/vusb.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk