[Erez & Jack] Removes keyboards which are not active on qmk

1 files changed, 0 insertions, 149 deletions

diff --git a/keyboard/hhkb_qmk/Makefile b/keyboard/hhkb_qmk/Makefile
deleted file mode 100644
index 21ba261a23..0000000000
--- a/keyboard/hhkb_qmk/Makefile
+++ /dev/null
@@ -1,149 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-#                Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-#               (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-#            have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-#             have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-#               (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-#                (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-#              with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-#                   bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# Target file name (without extension).
-TARGET = hhkb_qmk
-
-
-# Directory common source filess exist
-TOP_DIR = ../..
-TMK_DIR = ../../tmk_core
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# # project specific files
-SRC = hhkb_qmk.c \
-      matrix.c
-
-ifdef KEYMAP
-    SRC := keymaps/keymaps/$(KEYMAP).c $(SRC)
-else
-    SRC := keymaps/keymaps/default.c $(SRC)
-endif
-
-CONFIG_H = config.h
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
-#OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-# as per original hasu settings
-OPT_DEFS += -DBOOTLOADER_SIZE=512
-
-# Build Options
-#   comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
-CONSOLE_ENABLE = yes	# Console for debug(+400)
-COMMAND_ENABLE = yes    # Commands for debug and configuration
-CUSTOM_MATRIX    = yes # Custom matrix file for the HHKB
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
-# NKRO_ENABLE = yes		# USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
-# MIDI_ENABLE = YES		# MIDI controls
-# UNICODE_ENABLE = YES		# Unicode
-# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
-
-
-# Optimize size but this may cause error "relocation truncated to fit"
-#EXTRALDFLAGS = -Wl,--relax
-
-# Search Path
-VPATH += $(TARGET_DIR)
-VPATH += $(TOP_DIR)
-VPATH += $(TMK_DIR)
-
-debug-on: EXTRAFLAGS += -DDEBUG -DDEBUG_ACTION
-debug-on: all
-
-debug-off: EXTRAFLAGS += -DNO_DEBUG -DNO_PRINT
-debug-off: OPT_DEFS := $(filter-out -DCONSOLE_ENABLE,$(OPT_DEFS))
-debug-off: all
-
-include $(TOP_DIR)/quantum/quantum.mk