Merge remote-tracking branch 'upstream/master'

3 files changed, 220 insertions, 220 deletions

diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c
index 31319ef575..2809c9d184 100644
--- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.c
@@ -1,49 +1,49 @@
-/*

-    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

-

-    Licensed under the Apache License, Version 2.0 (the "License");

-    you may not use this file except in compliance with the License.

-    You may obtain a copy of the License at

-

-        http://www.apache.org/licenses/LICENSE-2.0

-

-    Unless required by applicable law or agreed to in writing, software

-    distributed under the License is distributed on an "AS IS" BASIS,

-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

-    See the License for the specific language governing permissions and

-    limitations under the License.

-*/

-

-#include "hal.h"

-

-/**

- * @brief   PAL setup.

- * @details Digital I/O ports static configuration as defined in @p board.h.

- *          This variable is used by the HAL when initializing the PAL driver.

- */

-#if HAL_USE_PAL || defined(__DOXYGEN__)

-const PALConfig pal_default_config =

-{

-  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},

-  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},

-  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},

-  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},

-  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},

-};

-#endif

-

-/*

- * Early initialization code.

- * This initialization must be performed just after stack setup and before

- * any other initialization.

- */

-void __early_init(void) {

-

-  stm32_clock_init();

-}

-

-/*

- * Board-specific initialization code.

- */

-void boardInit(void) {

-}

+/*
+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#include "hal.h"
+
+/**
+ * @brief   PAL setup.
+ * @details Digital I/O ports static configuration as defined in @p board.h.
+ *          This variable is used by the HAL when initializing the PAL driver.
+ */
+#if HAL_USE_PAL || defined(__DOXYGEN__)
+const PALConfig pal_default_config =
+{
+  {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH},
+  {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH},
+  {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH},
+  {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH},
+  {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH},
+};
+#endif
+
+/*
+ * Early initialization code.
+ * This initialization must be performed just after stack setup and before
+ * any other initialization.
+ */
+void __early_init(void) {
+
+  stm32_clock_init();
+}
+
+/*
+ * Board-specific initialization code.
+ */
+void boardInit(void) {
+}
diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h
index 7253e77826..b31d74307b 100644
--- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.h
@@ -1,166 +1,166 @@
-/*

-    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio

-

-    Licensed under the Apache License, Version 2.0 (the "License");

-    you may not use this file except in compliance with the License.

-    You may obtain a copy of the License at

-

-        http://www.apache.org/licenses/LICENSE-2.0

-

-    Unless required by applicable law or agreed to in writing, software

-    distributed under the License is distributed on an "AS IS" BASIS,

-    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.

-    See the License for the specific language governing permissions and

-    limitations under the License.

-*/

-

-#ifndef _BOARD_H_

-#define _BOARD_H_

-

-/*

- * Setup for a Generic STM32F103 board.

- */

-

-/*

- * Board identifier.

- */

-#define BOARD_GENERIC_STM32_F103

-#define BOARD_NAME              "Generic STM32F103x board"

-

-/*

- * Board frequencies.

- */

-#define STM32_LSECLK            32768

-#define STM32_HSECLK            8000000

-

-/*

- * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.

- */

-#define STM32F103xB

-

-/*

- * IO pins assignments

- */

-

-/* on-board */

-

-#define GPIOC_LED               13

-#define GPIOD_OSC_IN            0

-#define GPIOD_OSC_OUT           1

-

-/* In case your board has a "USB enable" hardware

-   controlled by a pin, define it here. (It could be just

-   a 1.5k resistor connected to D+ line.)

-*/

-/*

-#define GPIOB_USB_DISC          10

-*/

-

-/*

- * I/O ports initial setup, this configuration is established soon after reset

- * in the initialization code.

- *

- * The digits have the following meaning:

- *   0 - Analog input.

- *   1 - Push Pull output 10MHz.

- *   2 - Push Pull output 2MHz.

- *   3 - Push Pull output 50MHz.

- *   4 - Digital input.

- *   5 - Open Drain output 10MHz.

- *   6 - Open Drain output 2MHz.

- *   7 - Open Drain output 50MHz.

- *   8 - Digital input with PullUp or PullDown resistor depending on ODR.

- *   9 - Alternate Push Pull output 10MHz.

- *   A - Alternate Push Pull output 2MHz.

- *   B - Alternate Push Pull output 50MHz.

- *   C - Reserved.

- *   D - Alternate Open Drain output 10MHz.

- *   E - Alternate Open Drain output 2MHz.

- *   F - Alternate Open Drain output 50MHz.

- * Please refer to the STM32 Reference Manual for details.

- */

-

-/*

- * Port A setup.

- * Everything input with pull-up except:

- * PA2  - Alternate output  (USART2 TX).

- * PA3  - Normal input      (USART2 RX).

- * PA9  - Alternate output  (USART1 TX).

- * PA10 - Normal input      (USART1 RX).

- */

-#define VAL_GPIOACRL            0x88884B88      /*  PA7...PA0 */

-#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */

-#define VAL_GPIOAODR            0xFFFFFFFF

-

-/*

- * Port B setup.

- * Everything input with pull-up except:

- * PB10    - Push Pull output  (USB switch).

- */

-#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */

-#define VAL_GPIOBCRH            0x88888388      /* PB15...PB8 */

-#define VAL_GPIOBODR            0xFFFFFFFF

-

-/*

- * Port C setup.

- * Everything input with pull-up except:

- * PC13    - Push Pull output  (LED).

- */

-#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */

-#define VAL_GPIOCCRH            0x88388888      /* PC15...PC8 */

-#define VAL_GPIOCODR            0xFFFFFFFF

-

-/*

- * Port D setup.

- * Everything input with pull-up except:

- * PD0  - Normal input (XTAL).

- * PD1  - Normal input (XTAL).

- */

-#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */

-#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */

-#define VAL_GPIODODR            0xFFFFFFFF

-

-/*

- * Port E setup.

- * Everything input with pull-up except:

- */

-#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */

-#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */

-#define VAL_GPIOEODR            0xFFFFFFFF

-

-/*

- * USB bus activation macro, required by the USB driver.

- */

-/* The point is that most of the generic STM32F103* boards

-   have a 1.5k resistor connected on one end to the D+ line

-   and on the other end to some pin. Or even a slightly more

-   complicated "USB enable" circuit, controlled by a pin.

-   That should go here.

-

-   However on some boards (e.g. one that I have), there's no

-   such hardware. In which case it's better to not do anything.

-*/

-/*

-#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)

-*/

-#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);

-

-/*

- * USB bus de-activation macro, required by the USB driver.

- */

-/*

-#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)

-*/

-#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);

-

-#if !defined(_FROM_ASM_)

-#ifdef __cplusplus

-extern "C" {

-#endif

-  void boardInit(void);

-#ifdef __cplusplus

-}

-#endif

-#endif /* _FROM_ASM_ */

-

-#endif /* _BOARD_H_ */

+/*
+    ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio
+
+    Licensed under the Apache License, Version 2.0 (the "License");
+    you may not use this file except in compliance with the License.
+    You may obtain a copy of the License at
+
+        http://www.apache.org/licenses/LICENSE-2.0
+
+    Unless required by applicable law or agreed to in writing, software
+    distributed under the License is distributed on an "AS IS" BASIS,
+    WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+    See the License for the specific language governing permissions and
+    limitations under the License.
+*/
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * Setup for a Generic STM32F103 board.
+ */
+
+/*
+ * Board identifier.
+ */
+#define BOARD_GENERIC_STM32_F103
+#define BOARD_NAME              "Generic STM32F103x board"
+
+/*
+ * Board frequencies.
+ */
+#define STM32_LSECLK            32768
+#define STM32_HSECLK            8000000
+
+/*
+ * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h.
+ */
+#define STM32F103xB
+
+/*
+ * IO pins assignments
+ */
+
+/* on-board */
+
+#define GPIOC_LED               13
+#define GPIOD_OSC_IN            0
+#define GPIOD_OSC_OUT           1
+
+/* In case your board has a "USB enable" hardware
+   controlled by a pin, define it here. (It could be just
+   a 1.5k resistor connected to D+ line.)
+*/
+/*
+#define GPIOB_USB_DISC          10
+*/
+
+/*
+ * I/O ports initial setup, this configuration is established soon after reset
+ * in the initialization code.
+ *
+ * The digits have the following meaning:
+ *   0 - Analog input.
+ *   1 - Push Pull output 10MHz.
+ *   2 - Push Pull output 2MHz.
+ *   3 - Push Pull output 50MHz.
+ *   4 - Digital input.
+ *   5 - Open Drain output 10MHz.
+ *   6 - Open Drain output 2MHz.
+ *   7 - Open Drain output 50MHz.
+ *   8 - Digital input with PullUp or PullDown resistor depending on ODR.
+ *   9 - Alternate Push Pull output 10MHz.
+ *   A - Alternate Push Pull output 2MHz.
+ *   B - Alternate Push Pull output 50MHz.
+ *   C - Reserved.
+ *   D - Alternate Open Drain output 10MHz.
+ *   E - Alternate Open Drain output 2MHz.
+ *   F - Alternate Open Drain output 50MHz.
+ * Please refer to the STM32 Reference Manual for details.
+ */
+
+/*
+ * Port A setup.
+ * Everything input with pull-up except:
+ * PA2  - Alternate output  (USART2 TX).
+ * PA3  - Normal input      (USART2 RX).
+ * PA9  - Alternate output  (USART1 TX).
+ * PA10 - Normal input      (USART1 RX).
+ */
+#define VAL_GPIOACRL            0x88884B88      /*  PA7...PA0 */
+#define VAL_GPIOACRH            0x888884B8      /* PA15...PA8 */
+#define VAL_GPIOAODR            0xFFFFFFFF
+
+/*
+ * Port B setup.
+ * Everything input with pull-up except:
+ * PB10    - Push Pull output  (USB switch).
+ */
+#define VAL_GPIOBCRL            0x88888888      /*  PB7...PB0 */
+#define VAL_GPIOBCRH            0x88888388      /* PB15...PB8 */
+#define VAL_GPIOBODR            0xFFFFFFFF
+
+/*
+ * Port C setup.
+ * Everything input with pull-up except:
+ * PC13    - Push Pull output  (LED).
+ */
+#define VAL_GPIOCCRL            0x88888888      /*  PC7...PC0 */
+#define VAL_GPIOCCRH            0x88388888      /* PC15...PC8 */
+#define VAL_GPIOCODR            0xFFFFFFFF
+
+/*
+ * Port D setup.
+ * Everything input with pull-up except:
+ * PD0  - Normal input (XTAL).
+ * PD1  - Normal input (XTAL).
+ */
+#define VAL_GPIODCRL            0x88888844      /*  PD7...PD0 */
+#define VAL_GPIODCRH            0x88888888      /* PD15...PD8 */
+#define VAL_GPIODODR            0xFFFFFFFF
+
+/*
+ * Port E setup.
+ * Everything input with pull-up except:
+ */
+#define VAL_GPIOECRL            0x88888888      /*  PE7...PE0 */
+#define VAL_GPIOECRH            0x88888888      /* PE15...PE8 */
+#define VAL_GPIOEODR            0xFFFFFFFF
+
+/*
+ * USB bus activation macro, required by the USB driver.
+ */
+/* The point is that most of the generic STM32F103* boards
+   have a 1.5k resistor connected on one end to the D+ line
+   and on the other end to some pin. Or even a slightly more
+   complicated "USB enable" circuit, controlled by a pin.
+   That should go here.
+
+   However on some boards (e.g. one that I have), there's no
+   such hardware. In which case it's better to not do anything.
+*/
+/*
+#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT);
+
+/*
+ * USB bus de-activation macro, required by the USB driver.
+ */
+/*
+#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC)
+*/
+#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12);
+
+#if !defined(_FROM_ASM_)
+#ifdef __cplusplus
+extern "C" {
+#endif
+  void boardInit(void);
+#ifdef __cplusplus
+}
+#endif
+#endif /* _FROM_ASM_ */
+
+#endif /* _BOARD_H_ */
diff --git a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk
index d692c0ee46..48e0e51fe6 100644
--- a/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk
+++ b/keyboards/chibios_test/boards/GENERIC_STM32_F103/board.mk
@@ -1,5 +1,5 @@
-# List of all the board related files.

-BOARDSRC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103/board.c

-

-# Required include directories

-BOARDINC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103

+# List of all the board related files.
+BOARDSRC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103/board.c
+
+# Required include directories
+BOARDINC = $(KEYBOARD_PATH)/boards/GENERIC_STM32_F103