DO NOT USE Merge branch 'master' into debounce_refactor

Merged, however now there are two debounce.h and debounce.c to mess around with and coalesce.
# Conflicts:
#	quantum/matrix.c

1 files changed, 8 insertions, 52 deletions

diff --git a/keyboards/clueboard/2x1800/rules.mk b/keyboards/clueboard/2x1800/rules.mk
index 516a536f6b..eb679b9fb7 100644
--- a/keyboards/clueboard/2x1800/rules.mk
+++ b/keyboards/clueboard/2x1800/rules.mk
@@ -1,64 +1,20 @@
-# MCU name
+# MCU details
 MCU = at90usb1286
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
 F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
 ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
 F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
 OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-#   Teensy halfKay   512
-#   Teensy++ halfKay 1024
-#   Atmel DFU loader 4096
-#   LUFA bootloader  4096
-#   USBaspLoader     2048
 OPT_DEFS += -DBOOTLOADER_SIZE=1024
 
 
 # Build Options
-#   change yes to no to disable
-#
-BOOTMAGIC_ENABLE = no      # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
 CONSOLE_ENABLE = yes        # Console for debug(+400)
-COMMAND_ENABLE = yes        # Commands for debug and configuration
-# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-NKRO_ENABLE = yes            # USB Nkey Rollover
+COMMAND_ENABLE = no         # Commands for debug and configuration
+NKRO_ENABLE = yes           # USB Nkey Rollover
 MIDI_ENABLE = no            # MIDI support (+2400 to 4200, depending on config)
 UNICODE_ENABLE = no         # Unicode
-RGBLIGHT_ENABLE = no        # RGB on port C6
-AUDIO_ENABLE = no           # Audio output on port C4 and B7
-FAUXCLICKY_ENABLE = no      # Use buzzer to emulate clicky switches
+RGBLIGHT_ENABLE = yes       # RGB on port C6
+AUDIO_ENABLE = yes          # Audio output on port C4 and B7