Merged branch master into bone2planck

1 files changed, 89 insertions, 0 deletions

diff --git a/keyboards/handwired/traveller/Makefile b/keyboards/handwired/traveller/Makefile
new file mode 100644
index 0000000000..12a4b71f4e
--- /dev/null
+++ b/keyboards/handwired/traveller/Makefile
@@ -0,0 +1,89 @@
+
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+# for avr upload
+USB ?= /dev/cu.usbmodem1421
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+
+ifdef TEENSY2
+    OPT_DEFS += -DATREUS_TEENSY2
+    ATREUS_UPLOAD_COMMAND = teensy_loader_cli -w -mmcu=$(MCU) $(TARGET).hex
+else
+    OPT_DEFS += -DATREUS_ASTAR
+    OPT_DEFS += -DCATERINA_BOOTLOADER
+    ATREUS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \
+                            avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB)
+endif
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# MCU name
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= no        # Console for debug(+400)
+COMMAND_ENABLE ?= no        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no            # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+RGBLIGHT_ENABLE = yes
+
+ifndef QUANTUM_DIR
+	include ../../../Makefile
+endif
+
+upload: build
+	$(ATREUS_UPLOAD_COMMAND)
+