Merge pull request #624 from Xyverz/master

Added Ergodox Layout with persistent layers, Atreus corrections

13 files changed, 564 insertions, 0 deletions

diff --git a/keyboards/tv44/Makefile b/keyboards/tv44/Makefile
new file mode 100644
index 0000000000..45ca127807
--- /dev/null
+++ b/keyboards/tv44/Makefile
@@ -0,0 +1,75 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+#   Teensy halfKay   512
+#   Teensy++ halfKay 1024
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+#   USBaspLoader     2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+#   change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= yes      # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes       # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes        # Console for debug(+400)
+COMMAND_ENABLE ?= yes        # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no       # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= yes           # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no       # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no            # MIDI controls
+UNICODE_ENABLE ?= no         # Unicode
+BLUETOOTH_ENABLE ?= no       # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no           # Audio output on port C6
+
+ifndef QUANTUM_DIR
+	include ../../Makefile
+endif
+
+
diff --git a/keyboards/tv44/config.h b/keyboards/tv44/config.h
new file mode 100644
index 0000000000..0ae93c0957
--- /dev/null
+++ b/keyboards/tv44/config.h
@@ -0,0 +1,162 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID       0xFEAE
+#define PRODUCT_ID      0x8844
+#define DEVICE_VER      0x0002
+#define MANUFACTURER    Evan Sailer
+#define PRODUCT         TheVan 44
+#define DESCRIPTION     keyboard firmware for TV44
+
+/* key matrix size */
+#define MATRIX_ROWS 4
+#define MATRIX_COLS 12
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ *                  ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { D7, B5, F7, D4 }
+#define MATRIX_COL_PINS { D2, D3, D5, D6, B4, B6, F6, F5, F4, F1, F0, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+ 
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+    keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS  true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1          H
+//#define MAGIC_KEY_HELP2          SLASH
+//#define MAGIC_KEY_DEBUG          D
+//#define MAGIC_KEY_DEBUG_MATRIX   X
+//#define MAGIC_KEY_DEBUG_KBD      K
+//#define MAGIC_KEY_DEBUG_MOUSE    M
+//#define MAGIC_KEY_VERSION        V
+//#define MAGIC_KEY_STATUS         S
+//#define MAGIC_KEY_CONSOLE        C
+//#define MAGIC_KEY_LAYER0_ALT1    ESC
+//#define MAGIC_KEY_LAYER0_ALT2    GRAVE
+//#define MAGIC_KEY_LAYER0         0
+//#define MAGIC_KEY_LAYER1         1
+//#define MAGIC_KEY_LAYER2         2
+//#define MAGIC_KEY_LAYER3         3
+//#define MAGIC_KEY_LAYER4         4
+//#define MAGIC_KEY_LAYER5         5
+//#define MAGIC_KEY_LAYER6         6
+//#define MAGIC_KEY_LAYER7         7
+//#define MAGIC_KEY_LAYER8         8
+//#define MAGIC_KEY_LAYER9         9
+//#define MAGIC_KEY_BOOTLOADER     PAUSE
+//#define MAGIC_KEY_LOCK           CAPS
+//#define MAGIC_KEY_EEPROM         E
+//#define MAGIC_KEY_NKRO           N
+//#define MAGIC_KEY_SLEEP_LED      Z
+
+/*
+ * Feature disable options
+ *  These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/tv44/keymaps/default/Makefile b/keyboards/tv44/keymaps/default/Makefile
new file mode 100644
index 0000000000..f4671a9d11
--- /dev/null
+++ b/keyboards/tv44/keymaps/default/Makefile
@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/tv44/keymaps/default/config.h b/keyboards/tv44/keymaps/default/config.h
new file mode 100644
index 0000000000..df06a26206
--- /dev/null
+++ b/keyboards/tv44/keymaps/default/config.h
@@ -0,0 +1,8 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif
\ No newline at end of file
diff --git a/keyboards/tv44/keymaps/default/keymap.c b/keyboards/tv44/keymaps/default/keymap.c
new file mode 100644
index 0000000000..6a4fef3da2
--- /dev/null
+++ b/keyboards/tv44/keymaps/default/keymap.c
@@ -0,0 +1,97 @@
+#include "tv44.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+// Each layer gets a name for readability, which is then used in the keymap matrix below.
+// The underscores don't mean anything - you can have a layer called STUFF or any other name.
+// Layer names don't all need to be of the same length, obviously, and you can also skip them
+// entirely and just use numbers.
+
+#define _QW 0
+#define _DV 1
+#define _CM 2
+#define _L1 3
+#define _L2 4
+#define _L3 5
+
+// Macro name shortcuts
+#define QWERTY M(_QW)
+#define DVORAK M(_DV)
+#define COLEMAK M(_CM)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_QW] = { /* Qwerty */
+    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC },
+    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, MO(_L1) },
+    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_F,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) },
+    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
+  },
+  [_DV] = { /* Dvorak */
+    {KC_TAB,  KC_COMM, KC_DOT,  KC_SLSH, KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_Q,    KC_BSPC },
+    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    MO(_L1) },
+    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    MO(_L2) },
+    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
+  },
+  [_CM] = { /* Colemak */
+    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC },
+    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    MO(_L1) },
+    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, MO(_L2) },
+    {KC_LCTL, MO(_L2), KC_LGUI, KC_ENT,  XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_RALT, KC_ESC,  XXXXXXX, TG(_L3) }
+  },
+  [_L1] = { /* LAYER 1 */
+    {KC_GRV,  KC_EXLM, KC_AT,   KC_HASH, KC_DLR,  KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL  },
+    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ },
+    {_______, KC_ESC,  _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
+    {_______, KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
+  },
+  [_L2] = { /* LAYER 2 */
+    {_______, QWERTY,  DVORAK,  COLEMAK, _______, _______, _______, KC_7,    KC_8,    KC_9,    KC_0,    _______ },
+    {KC_ESC,  KC_PIPE, KC_DQUO, KC_UNDS, KC_PLUS, LSFT(KC_LBRC), LSFT(KC_RBRC), KC_4,    KC_5,    KC_6,    KC_VOLU, KC_ENT  },
+    {_______, _______, _______, _______, _______, _______, KC_0,    KC_1,    KC_2,    KC_3,    KC_VOLD, _______ },
+    {_______, _______, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, XXXXXXX, _______ }
+  },
+  [_L3] = { /* LAYER 3 */
+    {_______, _______, _______, _______, _______, _______, _______, KC_F1,   KC_F2,   KC_F3,   KC_F4,   _______ },
+    {KC_ESC,  _______, _______, _______, _______, _______, _______, KC_F5,   KC_F6,   KC_F7,   KC_F8,   _______ },
+    {KC_LSFT, KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_F9,   KC_F10,  KC_F11,  KC_F12,  _______ },
+    {_______, KC_LSFT, KC_B,    KC_SPC,  XXXXXXX, XXXXXXX, XXXXXXX, KC_C,    _______, _______, XXXXXXX, _______ }
+  }
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+  eeconfig_update_default_layer(default_layer);
+  default_layer_set(default_layer);
+}
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+      switch(id) {
+        case _DV:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_DV);
+          }
+          break;
+        case _QW:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_QW);
+          }
+          break;
+        case _CM:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_CM);
+          }
+          break;
+      }
+    return MACRO_NONE;
+};
diff --git a/keyboards/tv44/keymaps/default/readme.md b/keyboards/tv44/keymaps/default/readme.md
new file mode 100644
index 0000000000..ac84c08cfa
--- /dev/null
+++ b/keyboards/tv44/keymaps/default/readme.md
@@ -0,0 +1 @@
+# The default keymap for tv44
\ No newline at end of file
diff --git a/keyboards/tv44/keymaps/xyverz/Makefile b/keyboards/tv44/keymaps/xyverz/Makefile
new file mode 100644
index 0000000000..f4671a9d11
--- /dev/null
+++ b/keyboards/tv44/keymaps/xyverz/Makefile
@@ -0,0 +1,21 @@
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in 
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = yes        # Commands for debug and configuration
+NKRO_ENABLE = yes           # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no       # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.  Do not enable this with audio at the same time.
+SLEEP_LED_ENABLE = no       # Breathing sleep LED during USB suspend
+
+ifndef QUANTUM_DIR
+	include ../../../../Makefile
+endif
\ No newline at end of file
diff --git a/keyboards/tv44/keymaps/xyverz/config.h b/keyboards/tv44/keymaps/xyverz/config.h
new file mode 100644
index 0000000000..df06a26206
--- /dev/null
+++ b/keyboards/tv44/keymaps/xyverz/config.h
@@ -0,0 +1,8 @@
+#ifndef CONFIG_USER_H
+#define CONFIG_USER_H
+
+#include "../../config.h"
+
+// place overrides here
+
+#endif
\ No newline at end of file
diff --git a/keyboards/tv44/keymaps/xyverz/keymap.c b/keyboards/tv44/keymaps/xyverz/keymap.c
new file mode 100644
index 0000000000..8cbcf8d35a
--- /dev/null
+++ b/keyboards/tv44/keymaps/xyverz/keymap.c
@@ -0,0 +1,92 @@
+#include "tv44.h"
+#include "action_layer.h"
+#include "eeconfig.h"
+
+extern keymap_config_t keymap_config;
+
+#define _DV 0
+#define _QW 1
+#define _CM 2
+#define _L1 3
+#define _L2 4
+
+// Macro name shortcuts
+#define DVORAK M(_DV)
+#define QWERTY M(_QW)
+#define COLEMAK M(_CM)
+
+// Fillers to make layering more clear
+#define _______ KC_TRNS
+#define XXXXXXX KC_NO
+
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+  [_DV] = { /* 0: Dvorak */
+    {KC_TAB,  KC_QUOT, KC_COMM, KC_DOT,  KC_P,    KC_Y,    KC_F,    KC_G,    KC_C,    KC_R,    KC_L,    KC_BSPC },
+    {MO(_L1), KC_A,    KC_O,    KC_E,    KC_U,    KC_I,    KC_D,    KC_H,    KC_T,    KC_N,    KC_S,    KC_ENT  },
+    {KC_LSFT, KC_SCLN, KC_Q,    KC_J,    KC_K,    KC_X,    KC_B,    KC_M,    KC_W,    KC_V,    KC_Z,    KC_RSFT },
+    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+  },
+
+  [_QW] = { /* 1: Qwerty */
+    {KC_TAB,  KC_Q,    KC_W,    KC_E,    KC_R,    KC_T,    KC_Y,    KC_U,    KC_I,    KC_O,    KC_P,    KC_BSPC },
+    {MO(_L1), KC_A,    KC_S,    KC_D,    KC_F,    KC_G,    KC_H,    KC_J,    KC_K,    KC_L,    KC_SCLN, KC_ENT  },
+    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_N,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
+    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+  },
+
+  [_CM] = { /* 2: Colemak */
+    {KC_TAB,  KC_Q,    KC_W,    KC_F,    KC_P,    KC_G,    KC_J,    KC_L,    KC_U,    KC_Y,    KC_SCLN, KC_BSPC },
+    {MO(_L1), KC_A,    KC_R,    KC_S,    KC_T,    KC_D,    KC_H,    KC_N,    KC_E,    KC_I,    KC_O,    KC_ENT  },
+    {KC_LSFT, KC_Z,    KC_X,    KC_C,    KC_V,    KC_B,    KC_K,    KC_M,    KC_COMM, KC_DOT,  KC_SLSH, KC_RSFT },
+    {KC_LCTL, KC_LALT, KC_LGUI, KC_BSPC, XXXXXXX, XXXXXXX, XXXXXXX, KC_SPC,  KC_SLSH, KC_MINS, XXXXXXX, MO(_L2) }
+  },
+
+  [_L1] = {/* 1: FN 1 */
+    {KC_GRV,  KC_1,    KC_2,    KC_3,    KC_4,    KC_5,    KC_6,    KC_7,    KC_8,    KC_9,    KC_0,    KC_DEL  },
+    {_______, KC_BSLS, KC_QUOT, KC_MINS, KC_EQL,  KC_LBRC, KC_RBRC, KC_DOWN, KC_UP,   KC_LEFT, KC_RGHT, _______ },
+    {_______, _______, _______, KC_PSCR, _______, _______, _______, KC_MSTP, KC_MPLY, KC_MPRV, KC_MNXT, KC_RSFT },
+    {KC_ESC,  KC_LGUI, _______, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, KC_SLSH, _______, _______ }
+  },
+
+  [_L2] = { /* 2: FN 2 */
+    {KC_ESC,  KC_F1,   KC_F2,   KC_F3,   KC_F4,   KC_F5,   KC_F6,   KC_F7,   KC_F8,   KC_F9,   KC_F10,  KC_ESC  },
+    {_______, KC_F11,  KC_F12,  _______, _______, _______, _______, _______, KC_HOME, KC_PGUP, KC_VOLU, KC_ENT  },
+    {_______, _______, _______, _______, _______, _______, _______, _______, KC_END,  KC_PGDN, KC_VOLD, _______ },
+    {QWERTY,  DVORAK,  COLEMAK, _______, XXXXXXX, XXXXXXX, XXXXXXX, _______, _______, _______, _______, _______ }
+  }
+
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+void persistant_default_layer_set(uint16_t default_layer) {
+  eeconfig_update_default_layer(default_layer);
+  default_layer_set(default_layer);
+}
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+      switch(id) {
+        case _DV:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_DV);
+          }
+          break;
+        case _QW:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_QW);
+          }
+          break;
+        case _CM:
+          if (record->event.pressed) {
+            persistant_default_layer_set(1UL<<_CM);
+          }
+          break;
+      }
+    return MACRO_NONE;
+};
+
+
diff --git a/keyboards/tv44/keymaps/xyverz/readme.md b/keyboards/tv44/keymaps/xyverz/readme.md
new file mode 100644
index 0000000000..ac84c08cfa
--- /dev/null
+++ b/keyboards/tv44/keymaps/xyverz/readme.md
@@ -0,0 +1 @@
+# The default keymap for tv44
\ No newline at end of file
diff --git a/keyboards/tv44/readme.md b/keyboards/tv44/readme.md
new file mode 100644
index 0000000000..e3b557fe2d
--- /dev/null
+++ b/keyboards/tv44/readme.md
@@ -0,0 +1,28 @@
+tv44 keyboard firmware
+======================
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/tv44 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. 
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create a folder with the name of your keymap in the keymaps folder, and see keymap documentation (you can find in top readme.md) and existant keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+
+```
+$ make keymap=[default|jack|<name>]
+```
+
+Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
\ No newline at end of file
diff --git a/keyboards/tv44/tv44.c b/keyboards/tv44/tv44.c
new file mode 100644
index 0000000000..6dc0efd28e
--- /dev/null
+++ b/keyboards/tv44/tv44.c
@@ -0,0 +1,28 @@
+#include "tv44.h"
+
+void matrix_init_kb(void) {
+	// put your keyboard start-up code here
+	// runs once when the firmware starts up
+
+	matrix_init_user();
+}
+
+void matrix_scan_kb(void) {
+	// put your looping keyboard code here
+	// runs every cycle (a lot)
+
+	matrix_scan_user();
+}
+
+bool process_record_kb(uint16_t keycode, keyrecord_t *record) {
+	// put your per-action keyboard code here
+	// runs for every action, just before processing by the firmware
+
+	return process_record_user(keycode, record);
+}
+
+void led_set_kb(uint8_t usb_led) {
+	// put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+	led_set_user(usb_led);
+}
diff --git a/keyboards/tv44/tv44.h b/keyboards/tv44/tv44.h
new file mode 100644
index 0000000000..4c30174acc
--- /dev/null
+++ b/keyboards/tv44/tv44.h
@@ -0,0 +1,22 @@
+#ifndef TV44_H
+#define TV44_H
+
+#include "quantum.h"
+
+// This a shortcut to help you visually see your layout.
+// The following is an example using the Planck MIT layout
+// The first section contains all of the arguements
+// The second converts the arguments into a two-dimensional array
+#define KEYMAP( \
+    K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, \
+    K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, \
+    K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, \
+    K30, K31, K32, K33,           K37, K38,      K39,      K3B  \
+) \
+{ \
+    { K00,   K01,   K02,   K03,  K04,   K05,   K06,   K07,   K08,   K09,   K0A,   K0B }, \
+    { K10,   K11,   K12,   K13,  K14,   K15,   K16,   K17,   K18,   K19,   K1A,   K1B }, \
+    { K20,   K21,   K22,   K23,  K24,   K25,   K26,   K27,   K28,   K29,   K2A,   K2B }, \
+    { K30,   K31,   K32,   K33,  KC_NO, KC_NO, KC_NO, K37,   K38,   K39,   K3A,   K3B }  \
+
+#endif