Fixe line endings

1 files changed, 69 insertions, 69 deletions

diff --git a/keyboards/qwertyydox/rules.mk b/keyboards/qwertyydox/rules.mk
index d04a4b9f30..8c6171bc00 100644
--- a/keyboards/qwertyydox/rules.mk
+++ b/keyboards/qwertyydox/rules.mk
@@ -1,69 +1,69 @@
-# MCU name

-#MCU = at90usb1287

-MCU = atmega32u4

-

-# Processor frequency.

-#     This will define a symbol, F_CPU, in all source code files equal to the

-#     processor frequency in Hz. You can then use this symbol in your source code to

-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

-#     automatically to create a 32-bit value in your source code.

-#

-#     This will be an integer division of F_USB below, as it is sourced by

-#     F_USB after it has run through any CPU prescalers. Note that this value

-#     does not *change* the processor frequency - it should merely be updated to

-#     reflect the processor speed set externally so that the code can use accurate

-#     software delays.

-F_CPU = 16000000

-

-#

-# LUFA specific

-#

-# Target architecture (see library "Board Types" documentation).

-ARCH = AVR8

-

-# Input clock frequency.

-#     This will define a symbol, F_USB, in all source code files equal to the

-#     input clock frequency (before any prescaling is performed) in Hz. This value may

-#     differ from F_CPU if prescaling is used on the latter, and is required as the

-#     raw input clock is fed directly to the PLL sections of the AVR for high speed

-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'

-#     at the end, this will be done automatically to create a 32-bit value in your

-#     source code.

-#

-#     If no clock division is performed on the input clock inside the AVR (via the

-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.

-F_USB = $(F_CPU)

-

-# Bootloader

-#     This definition is optional, and if your keyboard supports multiple bootloaders of

-#     different sizes, comment this out, and the correct address will be loaded 

-#     automatically (+60). See bootloader.mk for all options.

-BOOTLOADER = caterina

-

-# Interrupt driven control endpoint task(+60)

-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

-

-# Build Options

-#   change to "no" to disable the options, or define them in the Makefile in

-#   the appropriate keymap folder that will get included automatically

-#

-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)

-MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)

-EXTRAKEY_ENABLE = no       # Audio control and System control(+450)

-CONSOLE_ENABLE = no         # Console for debug(+400)

-COMMAND_ENABLE = no        # Commands for debug and configuration

-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work

-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality

-MIDI_ENABLE = no            # MIDI controls

-AUDIO_ENABLE = no           # Audio output on port C6

-UNICODE_ENABLE = no         # Unicode

-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID

-RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight. 

-SUBPROJECT_rev1 = yes

-USE_I2C = yes               # I2C is used between the sides

-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE

-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend

-

-SPLIT_KEYBOARD = yes

-

-DEFAULT_FOLDER = qwertyydox/rev1

+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+#     This will define a symbol, F_CPU, in all source code files equal to the
+#     processor frequency in Hz. You can then use this symbol in your source code to
+#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+#     automatically to create a 32-bit value in your source code.
+#
+#     This will be an integer division of F_USB below, as it is sourced by
+#     F_USB after it has run through any CPU prescalers. Note that this value
+#     does not *change* the processor frequency - it should merely be updated to
+#     reflect the processor speed set externally so that the code can use accurate
+#     software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Bootloader
+#     This definition is optional, and if your keyboard supports multiple bootloaders of
+#     different sizes, comment this out, and the correct address will be loaded
+#     automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Build Options
+#   change to "no" to disable the options, or define them in the Makefile in
+#   the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes       # Mouse keys(+4700)
+EXTRAKEY_ENABLE = no       # Audio control and System control(+450)
+CONSOLE_ENABLE = no         # Console for debug(+400)
+COMMAND_ENABLE = no        # Commands for debug and configuration
+NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
+MIDI_ENABLE = no            # MIDI controls
+AUDIO_ENABLE = no           # Audio output on port C6
+UNICODE_ENABLE = no         # Unicode
+BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no       # Enable WS2812 RGB underlight.
+SUBPROJECT_rev1 = yes
+USE_I2C = yes               # I2C is used between the sides
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
+
+SPLIT_KEYBOARD = yes
+
+DEFAULT_FOLDER = qwertyydox/rev1