diff options
21 files changed, 2206 insertions, 0 deletions
diff --git a/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.c b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.c new file mode 100644 index 0000000000..8c5a87f35f --- /dev/null +++ b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.c @@ -0,0 +1,56 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#include "hal.h" + +// Value to place in RTC backup register 10 for persistent bootloader mode +#define RTC_BOOTLOADER_FLAG 0x424C + +/** + * @brief PAL setup. + * @details Digital I/O ports static configuration as defined in @p board.h. + * This variable is used by the HAL when initializing the PAL driver. + */ +#if HAL_USE_PAL || defined(__DOXYGEN__) +const PALConfig pal_default_config = +{ + {VAL_GPIOAODR, VAL_GPIOACRL, VAL_GPIOACRH}, + {VAL_GPIOBODR, VAL_GPIOBCRL, VAL_GPIOBCRH}, + {VAL_GPIOCODR, VAL_GPIOCCRL, VAL_GPIOCCRH}, + {VAL_GPIODODR, VAL_GPIODCRL, VAL_GPIODCRH}, + {VAL_GPIOEODR, VAL_GPIOECRL, VAL_GPIOECRH}, +}; +#endif + +/* + * Early initialization code. + * This initialization must be performed just after stack setup and before + * any other initialization. + */ +void __early_init(void) { + + stm32_clock_init(); +} + +/* + * Board-specific initialization code. + */ +void boardInit(void) { + //JTAG-DP Disabled and SW-DP Enabled + AFIO->MAPR |= AFIO_MAPR_SWJ_CFG_JTAGDISABLE; + //Set backup register DR10 to enter bootloader on reset + BKP->DR10 = RTC_BOOTLOADER_FLAG; +} diff --git a/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.h b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.h new file mode 100644 index 0000000000..9427adabf1 --- /dev/null +++ b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.h @@ -0,0 +1,166 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +/* + * Setup for a Generic STM32F103 board. + */ + +/* + * Board identifier. + */ +#define BOARD_GENERIC_STM32_F103 +#define BOARD_NAME "Generic STM32F103x board" + +/* + * Board frequencies. + */ +#define STM32_LSECLK 32768 +#define STM32_HSECLK 8000000 + +/* + * MCU type, supported types are defined in ./os/hal/platforms/hal_lld.h. + */ +#define STM32F103xB + +/* + * IO pins assignments + */ + +/* on-board */ + +#define GPIOA_LED 8 +#define GPIOD_OSC_IN 0 +#define GPIOD_OSC_OUT 1 + +/* In case your board has a "USB enable" hardware + controlled by a pin, define it here. (It could be just + a 1.5k resistor connected to D+ line.) +*/ +/* +#define GPIOB_USB_DISC 10 +*/ + +/* + * I/O ports initial setup, this configuration is established soon after reset + * in the initialization code. + * + * The digits have the following meaning: + * 0 - Analog input. + * 1 - Push Pull output 10MHz. + * 2 - Push Pull output 2MHz. + * 3 - Push Pull output 50MHz. + * 4 - Digital input. + * 5 - Open Drain output 10MHz. + * 6 - Open Drain output 2MHz. + * 7 - Open Drain output 50MHz. + * 8 - Digital input with PullUp or PullDown resistor depending on ODR. + * 9 - Alternate Push Pull output 10MHz. + * A - Alternate Push Pull output 2MHz. + * B - Alternate Push Pull output 50MHz. + * C - Reserved. + * D - Alternate Open Drain output 10MHz. + * E - Alternate Open Drain output 2MHz. + * F - Alternate Open Drain output 50MHz. + * Please refer to the STM32 Reference Manual for details. + */ + +/* + * Port A setup. + * Everything input with pull-up except: + * PA2 - Alternate output (USART2 TX). + * PA3 - Normal input (USART2 RX). + * PA9 - Alternate output (USART1 TX). + * PA10 - Normal input (USART1 RX). + */ +#define VAL_GPIOACRL 0x88884B88 /* PA7...PA0 */ +#define VAL_GPIOACRH 0x888884B8 /* PA15...PA8 */ +#define VAL_GPIOAODR 0xFFFFFFFF + +/* + * Port B setup. + * Everything input with pull-up except: + * PB10 - Push Pull output (USB switch). + */ +#define VAL_GPIOBCRL 0x88888888 /* PB7...PB0 */ +#define VAL_GPIOBCRH 0x88888388 /* PB15...PB8 */ +#define VAL_GPIOBODR 0xFFFFFFFF + +/* + * Port C setup. + * Everything input with pull-up except: + * PC13 - Push Pull output (LED). + */ +#define VAL_GPIOCCRL 0x88888888 /* PC7...PC0 */ +#define VAL_GPIOCCRH 0x88388888 /* PC15...PC8 */ +#define VAL_GPIOCODR 0xFFFFFFFF + +/* + * Port D setup. + * Everything input with pull-up except: + * PD0 - Normal input (XTAL). + * PD1 - Normal input (XTAL). + */ +#define VAL_GPIODCRL 0x88888844 /* PD7...PD0 */ +#define VAL_GPIODCRH 0x88888888 /* PD15...PD8 */ +#define VAL_GPIODODR 0xFFFFFFFF + +/* + * Port E setup. + * Everything input with pull-up except: + */ +#define VAL_GPIOECRL 0x88888888 /* PE7...PE0 */ +#define VAL_GPIOECRH 0x88888888 /* PE15...PE8 */ +#define VAL_GPIOEODR 0xFFFFFFFF + +/* + * USB bus activation macro, required by the USB driver. + */ +/* The point is that most of the generic STM32F103* boards + have a 1.5k resistor connected on one end to the D+ line + and on the other end to some pin. Or even a slightly more + complicated "USB enable" circuit, controlled by a pin. + That should go here. + + However on some boards (e.g. one that I have), there's no + such hardware. In which case it's better to not do anything. +*/ +/* +#define usb_lld_connect_bus(usbp) palClearPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_connect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_INPUT); + +/* + * USB bus de-activation macro, required by the USB driver. + */ +/* +#define usb_lld_disconnect_bus(usbp) palSetPad(GPIOB, GPIOB_USB_DISC) +*/ +#define usb_lld_disconnect_bus(usbp) palSetPadMode(GPIOA, 12, PAL_MODE_OUTPUT_PUSHPULL); palClearPad(GPIOA, 12); + +#if !defined(_FROM_ASM_) +#ifdef __cplusplus +extern "C" { +#endif + void boardInit(void); +#ifdef __cplusplus +} +#endif +#endif /* _FROM_ASM_ */ + +#endif /* _BOARD_H_ */ diff --git a/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.mk b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.mk new file mode 100644 index 0000000000..6b8b312fd9 --- /dev/null +++ b/keyboards/handwired/ortho60/boards/GENERIC_STM32_F103/board.mk @@ -0,0 +1,5 @@ +# List of all the board related files. +BOARDSRC = $(BOARD_PATH)/boards/GENERIC_STM32_F103/board.c + +# Required include directories +BOARDINC = $(BOARD_PATH)/boards/GENERIC_STM32_F103 diff --git a/keyboards/handwired/ortho60/bootloader_defs.h b/keyboards/handwired/ortho60/bootloader_defs.h new file mode 100644 index 0000000000..0f45203cb6 --- /dev/null +++ b/keyboards/handwired/ortho60/bootloader_defs.h @@ -0,0 +1,10 @@ +/* Address for jumping to bootloader on STM32 chips. */ +/* It is chip dependent, the correct number can be looked up here (page 175): + * http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf + * This also requires a patch to chibios: + * <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch + */ + +// STM32F103* does NOT have an USB bootloader in ROM (only serial), +// so setting anything here does not make much sense +// #define STM32_BOOTLOADER_ADDRESS 0x1FFFC800 diff --git a/keyboards/handwired/ortho60/chconf.h b/keyboards/handwired/ortho60/chconf.h new file mode 100644 index 0000000000..bbd9b2da62 --- /dev/null +++ b/keyboards/handwired/ortho60/chconf.h @@ -0,0 +1,524 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/chconf.h + * @brief Configuration file template. + * @details A copy of this file must be placed in each project directory, it + * contains the application specific kernel settings. + * + * @addtogroup config + * @details Kernel related settings and hooks. + * @{ + */ + +#ifndef CHCONF_H +#define CHCONF_H + +#define _CHIBIOS_RT_CONF_ + +/*===========================================================================*/ +/** + * @name System timers settings + * @{ + */ +/*===========================================================================*/ + +/** + * @brief System time counter resolution. + * @note Allowed values are 16 or 32 bits. + */ +#define CH_CFG_ST_RESOLUTION 32 + +/** + * @brief System tick frequency. + * @details Frequency of the system timer that drives the system ticks. This + * setting also defines the system tick time unit. + */ +#define CH_CFG_ST_FREQUENCY 100000 + +/** + * @brief Time delta constant for the tick-less mode. + * @note If this value is zero then the system uses the classic + * periodic tick. This value represents the minimum number + * of ticks that is safe to specify in a timeout directive. + * The value one is not valid, timeouts are rounded up to + * this value. + */ +#define CH_CFG_ST_TIMEDELTA 0 + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel parameters and options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Round robin interval. + * @details This constant is the number of system ticks allowed for the + * threads before preemption occurs. Setting this value to zero + * disables the preemption for threads with equal priority and the + * round robin becomes cooperative. Note that higher priority + * threads can still preempt, the kernel is always preemptive. + * @note Disabling the round robin preemption makes the kernel more compact + * and generally faster. + * @note The round robin preemption is not supported in tickless mode and + * must be set to zero in that case. + */ +#define CH_CFG_TIME_QUANTUM 0 + +/** + * @brief Managed RAM size. + * @details Size of the RAM area to be managed by the OS. If set to zero + * then the whole available RAM is used. The core memory is made + * available to the heap allocator and/or can be used directly through + * the simplified core memory allocator. + * + * @note In order to let the OS manage the whole RAM the linker script must + * provide the @p __heap_base__ and @p __heap_end__ symbols. + * @note Requires @p CH_CFG_USE_MEMCORE. + */ +#define CH_CFG_MEMCORE_SIZE 0 + +/** + * @brief Idle thread automatic spawn suppression. + * @details When this option is activated the function @p chSysInit() + * does not spawn the idle thread. The application @p main() + * function becomes the idle thread and must implement an + * infinite loop. + */ +#define CH_CFG_NO_IDLE_THREAD FALSE + +/* Use __WFI in the idle thread for waiting. Does lower the power + * consumption. */ +#define CORTEX_ENABLE_WFI_IDLE TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Performance options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief OS optimization. + * @details If enabled then time efficient rather than space efficient code + * is used when two possible implementations exist. + * + * @note This is not related to the compiler optimization options. + * @note The default is @p TRUE. + */ +#define CH_CFG_OPTIMIZE_SPEED TRUE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Subsystem options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Time Measurement APIs. + * @details If enabled then the time measurement APIs are included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_TM FALSE + +/** + * @brief Threads registry APIs. + * @details If enabled then the registry APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_REGISTRY TRUE + +/** + * @brief Threads synchronization APIs. + * @details If enabled then the @p chThdWait() function is included in + * the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_WAITEXIT TRUE + +/** + * @brief Semaphores APIs. + * @details If enabled then the Semaphores APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_SEMAPHORES TRUE + +/** + * @brief Semaphores queuing mode. + * @details If enabled then the threads are enqueued on semaphores by + * priority rather than in FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_SEMAPHORES_PRIORITY FALSE + +/** + * @brief Mutexes APIs. + * @details If enabled then the mutexes APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MUTEXES TRUE + +/** + * @brief Enables recursive behavior on mutexes. + * @note Recursive mutexes are heavier and have an increased + * memory footprint. + * + * @note The default is @p FALSE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_MUTEXES_RECURSIVE FALSE + +/** + * @brief Conditional Variables APIs. + * @details If enabled then the conditional variables APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MUTEXES. + */ +#define CH_CFG_USE_CONDVARS TRUE + +/** + * @brief Conditional Variables APIs with timeout. + * @details If enabled then the conditional variables APIs with timeout + * specification are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_CONDVARS. + */ +#define CH_CFG_USE_CONDVARS_TIMEOUT FALSE + +/** + * @brief Events Flags APIs. + * @details If enabled then the event flags APIs are included in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_EVENTS TRUE + +/** + * @brief Events Flags APIs with timeout. + * @details If enabled then the events APIs with timeout specification + * are included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_EVENTS. + */ +#define CH_CFG_USE_EVENTS_TIMEOUT TRUE + +/** + * @brief Synchronous Messages APIs. + * @details If enabled then the synchronous messages APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MESSAGES TRUE + +/** + * @brief Synchronous Messages queuing mode. + * @details If enabled then messages are served by priority rather than in + * FIFO order. + * + * @note The default is @p FALSE. Enable this if you have special + * requirements. + * @note Requires @p CH_CFG_USE_MESSAGES. + */ +#define CH_CFG_USE_MESSAGES_PRIORITY FALSE + +/** + * @brief Mailboxes APIs. + * @details If enabled then the asynchronous messages (mailboxes) APIs are + * included in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_SEMAPHORES. + */ +#define CH_CFG_USE_MAILBOXES TRUE + +/** + * @brief Core Memory Manager APIs. + * @details If enabled then the core memory manager APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMCORE TRUE + +/** + * @brief Heap Allocator APIs. + * @details If enabled then the memory heap allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_MEMCORE and either @p CH_CFG_USE_MUTEXES or + * @p CH_CFG_USE_SEMAPHORES. + * @note Mutexes are recommended. + */ +#define CH_CFG_USE_HEAP TRUE + +/** + * @brief Memory Pools Allocator APIs. + * @details If enabled then the memory pools allocator APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + */ +#define CH_CFG_USE_MEMPOOLS FALSE + +/** + * @brief Dynamic Threads APIs. + * @details If enabled then the dynamic threads creation APIs are included + * in the kernel. + * + * @note The default is @p TRUE. + * @note Requires @p CH_CFG_USE_WAITEXIT. + * @note Requires @p CH_CFG_USE_HEAP and/or @p CH_CFG_USE_MEMPOOLS. + */ +#define CH_CFG_USE_DYNAMIC FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Debug options + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Debug option, kernel statistics. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_STATISTICS FALSE + +/** + * @brief Debug option, system state check. + * @details If enabled the correct call protocol for system APIs is checked + * at runtime. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_SYSTEM_STATE_CHECK FALSE + +/** + * @brief Debug option, parameters checks. + * @details If enabled then the checks on the API functions input + * parameters are activated. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_CHECKS FALSE + +/** + * @brief Debug option, consistency checks. + * @details If enabled then all the assertions in the kernel code are + * activated. This includes consistency checks inside the kernel, + * runtime anomalies and port-defined checks. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_ENABLE_ASSERTS FALSE + +/** + * @brief Debug option, trace buffer. + * @details If enabled then the trace buffer is activated. + * + * @note The default is @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_MASK CH_DBG_TRACE_MASK_DISABLED + +/** + * @brief Trace buffer entries. + * @note The trace buffer is only allocated if @p CH_DBG_TRACE_MASK is + * different from @p CH_DBG_TRACE_MASK_DISABLED. + */ +#define CH_DBG_TRACE_BUFFER_SIZE 128 + +/** + * @brief Debug option, stack checks. + * @details If enabled then a runtime stack check is performed. + * + * @note The default is @p FALSE. + * @note The stack check is performed in a architecture/port dependent way. + * It may not be implemented or some ports. + * @note The default failure mode is to halt the system with the global + * @p panic_msg variable set to @p NULL. + */ +#define CH_DBG_ENABLE_STACK_CHECK FALSE + +/** + * @brief Debug option, stacks initialization. + * @details If enabled then the threads working area is filled with a byte + * value when a thread is created. This can be useful for the + * runtime measurement of the used stack. + * + * @note The default is @p FALSE. + */ +#define CH_DBG_FILL_THREADS FALSE + +/** + * @brief Debug option, threads profiling. + * @details If enabled then a field is added to the @p thread_t structure that + * counts the system ticks occurred while executing the thread. + * + * @note The default is @p FALSE. + * @note This debug option is not currently compatible with the + * tickless mode. + */ +#define CH_DBG_THREADS_PROFILING FALSE + +/** @} */ + +/*===========================================================================*/ +/** + * @name Kernel hooks + * @{ + */ +/*===========================================================================*/ + +/** + * @brief Threads descriptor structure extension. + * @details User fields added to the end of the @p thread_t structure. + */ +#define CH_CFG_THREAD_EXTRA_FIELDS \ + /* Add threads custom fields here.*/ + +/** + * @brief Threads initialization hook. + * @details User initialization code added to the @p chThdInit() API. + * + * @note It is invoked from within @p chThdInit() and implicitly from all + * the threads creation APIs. + */ +#define CH_CFG_THREAD_INIT_HOOK(tp) { \ + /* Add threads initialization code here.*/ \ +} + +/** + * @brief Threads finalization hook. + * @details User finalization code added to the @p chThdExit() API. + */ +#define CH_CFG_THREAD_EXIT_HOOK(tp) { \ + /* Add threads finalization code here.*/ \ +} + +/** + * @brief Context switch hook. + * @details This hook is invoked just before switching between threads. + */ +#define CH_CFG_CONTEXT_SWITCH_HOOK(ntp, otp) { \ + /* Context switch code here.*/ \ +} + +/** + * @brief ISR enter hook. + */ +#define CH_CFG_IRQ_PROLOGUE_HOOK() { \ + /* IRQ prologue code here.*/ \ +} + +/** + * @brief ISR exit hook. + */ +#define CH_CFG_IRQ_EPILOGUE_HOOK() { \ + /* IRQ epilogue code here.*/ \ +} + +/** + * @brief Idle thread enter hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to activate a power saving mode. + */ +#define CH_CFG_IDLE_ENTER_HOOK() { \ + /* Idle-enter code here.*/ \ +} + +/** + * @brief Idle thread leave hook. + * @note This hook is invoked within a critical zone, no OS functions + * should be invoked from here. + * @note This macro can be used to deactivate a power saving mode. + */ +#define CH_CFG_IDLE_LEAVE_HOOK() { \ + /* Idle-leave code here.*/ \ +} + +/** + * @brief Idle Loop hook. + * @details This hook is continuously invoked by the idle thread loop. + */ +#define CH_CFG_IDLE_LOOP_HOOK() { \ + /* Idle loop code here.*/ \ +} + +/** + * @brief System tick event hook. + * @details This hook is invoked in the system tick handler immediately + * after processing the virtual timers queue. + */ +#define CH_CFG_SYSTEM_TICK_HOOK() { \ + /* System tick event code here.*/ \ +} + +/** + * @brief System halt hook. + * @details This hook is invoked in case to a system halting error before + * the system is halted. + */ +#define CH_CFG_SYSTEM_HALT_HOOK(reason) { \ + /* System halt code here.*/ \ +} + +/** + * @brief Trace hook. + * @details This hook is invoked each time a new record is written in the + * trace buffer. + */ +#define CH_CFG_TRACE_HOOK(tep) { \ + /* Trace code here.*/ \ +} + +/** @} */ + +/*===========================================================================*/ +/* Port-specific settings (override port settings defaulted in chcore.h). */ +/*===========================================================================*/ + +#endif /* CHCONF_H */ + +/** @} */ diff --git a/keyboards/handwired/ortho60/config.h b/keyboards/handwired/ortho60/config.h new file mode 100644 index 0000000000..dd06f3f953 --- /dev/null +++ b/keyboards/handwired/ortho60/config.h @@ -0,0 +1,74 @@ +/* +Copyright 2015 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#pragma once + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6464 +#define DEVICE_VER 0x0001 +/* in python2: list(u"whatever".encode('utf-16-le')) */ +/* at most 32 characters or the ugly hack in usb_main.c borks */ +#define MANUFACTURER QMK +#define PRODUCT Ortho60 +#define DESCRIPTION Ortho60 + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 12 + +#define MATRIX_COL_PINS { B11, B10, B1, B0, A7, A6, A5, A4, A3, A2, A1, A0 } +#define MATRIX_ROW_PINS { B3, B4, B5, B6, B7 } +#define DIODE_DIRECTION COL2ROW + +#define BACKLIGHT_LEVELS 1 + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + + + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION diff --git a/keyboards/handwired/ortho60/halconf.h b/keyboards/handwired/ortho60/halconf.h new file mode 100644 index 0000000000..5fba285a38 --- /dev/null +++ b/keyboards/handwired/ortho60/halconf.h @@ -0,0 +1,353 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/** + * @file templates/halconf.h + * @brief HAL configuration header. + * @details HAL configuration file, this file allows to enable or disable the + * various device drivers from your application. You may also use + * this file in order to override the device drivers default settings. + * + * @addtogroup HAL_CONF + * @{ + */ + +#ifndef _HALCONF_H_ +#define _HALCONF_H_ + +#include "mcuconf.h" + +/** + * @brief Enables the PAL subsystem. + */ +#if !defined(HAL_USE_PAL) || defined(__DOXYGEN__) +#define HAL_USE_PAL TRUE +#endif + +/** + * @brief Enables the ADC subsystem. + */ +#if !defined(HAL_USE_ADC) || defined(__DOXYGEN__) +#define HAL_USE_ADC FALSE +#endif + +/** + * @brief Enables the CAN subsystem. + */ +#if !defined(HAL_USE_CAN) || defined(__DOXYGEN__) +#define HAL_USE_CAN FALSE +#endif + +/** + * @brief Enables the DAC subsystem. + */ +#if !defined(HAL_USE_DAC) || defined(__DOXYGEN__) +#define HAL_USE_DAC FALSE +#endif + +/** + * @brief Enables the EXT subsystem. + */ +#if !defined(HAL_USE_EXT) || defined(__DOXYGEN__) +#define HAL_USE_EXT FALSE +#endif + +/** + * @brief Enables the GPT subsystem. + */ +#if !defined(HAL_USE_GPT) || defined(__DOXYGEN__) +#define HAL_USE_GPT FALSE +#endif + +/** + * @brief Enables the I2C subsystem. + */ +#if !defined(HAL_USE_I2C) || defined(__DOXYGEN__) +#define HAL_USE_I2C FALSE +#endif + +/** + * @brief Enables the I2S subsystem. + */ +#if !defined(HAL_USE_I2S) || defined(__DOXYGEN__) +#define HAL_USE_I2S FALSE +#endif + +/** + * @brief Enables the ICU subsystem. + */ +#if !defined(HAL_USE_ICU) || defined(__DOXYGEN__) +#define HAL_USE_ICU FALSE +#endif + +/** + * @brief Enables the MAC subsystem. + */ +#if !defined(HAL_USE_MAC) || defined(__DOXYGEN__) +#define HAL_USE_MAC FALSE +#endif + +/** + * @brief Enables the MMC_SPI subsystem. + */ +#if !defined(HAL_USE_MMC_SPI) || defined(__DOXYGEN__) +#define HAL_USE_MMC_SPI FALSE +#endif + +/** + * @brief Enables the PWM subsystem. + */ +#if !defined(HAL_USE_PWM) || defined(__DOXYGEN__) +#define HAL_USE_PWM FALSE +#endif + +/** + * @brief Enables the RTC subsystem. + */ +#if !defined(HAL_USE_RTC) || defined(__DOXYGEN__) +#define HAL_USE_RTC FALSE +#endif + +/** + * @brief Enables the SDC subsystem. + */ +#if !defined(HAL_USE_SDC) || defined(__DOXYGEN__) +#define HAL_USE_SDC FALSE +#endif + +/** + * @brief Enables the SERIAL subsystem. + */ +#if !defined(HAL_USE_SERIAL) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL FALSE +#endif + +/** + * @brief Enables the SERIAL over USB subsystem. + */ +#if !defined(HAL_USE_SERIAL_USB) || defined(__DOXYGEN__) +#define HAL_USE_SERIAL_USB FALSE +#endif + +/** + * @brief Enables the SPI subsystem. + */ +#if !defined(HAL_USE_SPI) || defined(__DOXYGEN__) +#define HAL_USE_SPI TRUE +#endif + +/** + * @brief Enables the UART subsystem. + */ +#if !defined(HAL_USE_UART) || defined(__DOXYGEN__) +#define HAL_USE_UART FALSE +#endif + +/** + * @brief Enables the USB subsystem. + */ +#if !defined(HAL_USE_USB) || defined(__DOXYGEN__) +#define HAL_USE_USB TRUE +#endif + +/** + * @brief Enables the WDG subsystem. + */ +#if !defined(HAL_USE_WDG) || defined(__DOXYGEN__) +#define HAL_USE_WDG FALSE +#endif + +/*===========================================================================*/ +/* ADC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_WAIT) || defined(__DOXYGEN__) +#define ADC_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p adcAcquireBus() and @p adcReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(ADC_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define ADC_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* CAN driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Sleep mode related APIs inclusion switch. + */ +#if !defined(CAN_USE_SLEEP_MODE) || defined(__DOXYGEN__) +#define CAN_USE_SLEEP_MODE TRUE +#endif + +/*===========================================================================*/ +/* I2C driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables the mutual exclusion APIs on the I2C bus. + */ +#if !defined(I2C_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define I2C_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* MAC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_ZERO_COPY) || defined(__DOXYGEN__) +#define MAC_USE_ZERO_COPY FALSE +#endif + +/** + * @brief Enables an event sources for incoming packets. + */ +#if !defined(MAC_USE_EVENTS) || defined(__DOXYGEN__) +#define MAC_USE_EVENTS TRUE +#endif + +/*===========================================================================*/ +/* MMC_SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + * This option is recommended also if the SPI driver does not + * use a DMA channel and heavily loads the CPU. + */ +#if !defined(MMC_NICE_WAITING) || defined(__DOXYGEN__) +#define MMC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SDC driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Number of initialization attempts before rejecting the card. + * @note Attempts are performed at 10mS intervals. + */ +#if !defined(SDC_INIT_RETRY) || defined(__DOXYGEN__) +#define SDC_INIT_RETRY 100 +#endif + +/** + * @brief Include support for MMC cards. + * @note MMC support is not yet implemented so this option must be kept + * at @p FALSE. + */ +#if !defined(SDC_MMC_SUPPORT) || defined(__DOXYGEN__) +#define SDC_MMC_SUPPORT FALSE +#endif + +/** + * @brief Delays insertions. + * @details If enabled this options inserts delays into the MMC waiting + * routines releasing some extra CPU time for the threads with + * lower priority, this may slow down the driver a bit however. + */ +#if !defined(SDC_NICE_WAITING) || defined(__DOXYGEN__) +#define SDC_NICE_WAITING TRUE +#endif + +/*===========================================================================*/ +/* SERIAL driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Default bit rate. + * @details Configuration parameter, this is the baud rate selected for the + * default configuration. + */ +#if !defined(SERIAL_DEFAULT_BITRATE) || defined(__DOXYGEN__) +#define SERIAL_DEFAULT_BITRATE 38400 +#endif + +/** + * @brief Serial buffers size. + * @details Configuration parameter, you can change the depth of the queue + * buffers depending on the requirements of your application. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_BUFFERS_SIZE 16 +#endif + +/*===========================================================================*/ +/* SERIAL_USB driver related setting. */ +/*===========================================================================*/ + +/** + * @brief Serial over USB buffers size. + * @details Configuration parameter, the buffer size must be a multiple of + * the USB data endpoint maximum packet size. + * @note The default is 64 bytes for both the transmission and receive + * buffers. + */ +#if !defined(SERIAL_USB_BUFFERS_SIZE) || defined(__DOXYGEN__) +#define SERIAL_USB_BUFFERS_SIZE 1 +#endif + +/*===========================================================================*/ +/* SPI driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_WAIT) || defined(__DOXYGEN__) +#define SPI_USE_WAIT TRUE +#endif + +/** + * @brief Enables the @p spiAcquireBus() and @p spiReleaseBus() APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(SPI_USE_MUTUAL_EXCLUSION) || defined(__DOXYGEN__) +#define SPI_USE_MUTUAL_EXCLUSION TRUE +#endif + +/*===========================================================================*/ +/* USB driver related settings. */ +/*===========================================================================*/ + +/** + * @brief Enables synchronous APIs. + * @note Disabling this option saves both code and data space. + */ +#if !defined(USB_USE_WAIT) || defined(__DOXYGEN__) +#define USB_USE_WAIT TRUE +#endif + +#endif /* _HALCONF_H_ */ + +/** @} */ diff --git a/keyboards/handwired/ortho60/hsv2rgb.c b/keyboards/handwired/ortho60/hsv2rgb.c new file mode 100644 index 0000000000..adb7af8fa5 --- /dev/null +++ b/keyboards/handwired/ortho60/hsv2rgb.c @@ -0,0 +1,80 @@ +/* hsv2rgb.c + * Integer only conversion functions between HSV and RGB + */ + +#include "hsv2rgb.h" + +// TODO fix these buggy macros +#define max(x,y) ((x>y) ? x:y) +#define min(x,y) ((x>y) ? y:x) +#define min3(x,y,z) (min(min(x,y),z)) +#define max3(x,y,z) (max(max(x,y),z)) + + +rgb_color hsv2rgb(hsv_color hsv) +{ + // From : http://qscribble.blogspot.fr/2008/06/integer-conversion-from-hsl-to-rgb.html + int h = hsv.h; + int s = hsv.s; + int v = hsv.v; + rgb_color rgb = {0, 0, 0}; + + if (v == 0) + return rgb; + + // sextant = 0 .. 5 + int sextant = (h*6)/256; + // f = 0 .. 42 + int f = h - (sextant*256)/6; + + int p = (v * (256 - s))/256; + int q = (v * (256*43 - s*f))/(256*43); + int t = (v * (256*43 - s*(43-f)))/(256*43); + + // Corrige les erreurs dues aux arrondis + p = max(min(p, 255), 0); + q = max(min(q, 255), 0); + t = max(min(t, 255), 0); + + switch(sextant){ + case 0: rgb.r = v; rgb.g = t; rgb.b = p; break; + case 1: rgb.r = q; rgb.g = v; rgb.b = p; break; + case 2: rgb.r = p; rgb.g = v; rgb.b = t; break; + case 3: rgb.r = p; rgb.g = q; rgb.b = v; break; + case 4: rgb.r = t; rgb.g = p; rgb.b = v; break; + default:rgb.r = v; rgb.g = p; rgb.b = q; break; + } + return rgb; +} + + +hsv_color rgb2hsv(rgb_color rgb) +{ + // From : http://www.ruinelli.ch/rgb-to-hsv + hsv_color hsv = {0, 0, 0}; + int min, max, delta; + + min = min3(rgb.r, rgb.g, rgb.b); + max = max3(rgb.r, rgb.g, rgb.b); + + if(max==0) { + hsv.h = 0; + hsv.s = 0; + hsv.v = 0; + return hsv; + } + + hsv.v = max; + delta = max - min; + + hsv.s = (delta)*255 / max; + + if(rgb.r == max) + hsv.h = (rgb.g - rgb.b)*42/delta; // between yellow & magenta + else if(rgb.g == max) + hsv.h = 120 + (rgb.b - rgb.r)*42/delta; // between cyan & yellow + else + hsv.h = 240 + (rgb.r - rgb.g)*42/delta; // between magenta & cyan + + return hsv; +}
\ No newline at end of file diff --git a/keyboards/handwired/ortho60/hsv2rgb.h b/keyboards/handwired/ortho60/hsv2rgb.h new file mode 100644 index 0000000000..99566c32c0 --- /dev/null +++ b/keyboards/handwired/ortho60/hsv2rgb.h @@ -0,0 +1,23 @@ +/* hsv2rgb.h + * Convert Hue Saturation Value to Red Green Blue + * + * Programme de convertion d'une information HSV en RGB + */ +#ifndef HSV2RGB_H +#define HSV2RGB_H + +typedef struct { + unsigned char h; + unsigned char s; + unsigned char v; +} hsv_color; + +typedef struct { + unsigned char r; + unsigned char g; + unsigned char b; +} rgb_color; + +rgb_color hsv2rgb(hsv_color hsv); + +#endif
\ No newline at end of file diff --git a/keyboards/handwired/ortho60/info.json b/keyboards/handwired/ortho60/info.json new file mode 100644 index 0000000000..b6e4854410 --- /dev/null +++ b/keyboards/handwired/ortho60/info.json @@ -0,0 +1,73 @@ +{ + "keyboard_name": "Ortho60", + "url": "", + "maintainer": "qmk", + "width": 12, + "height": 5, + "layouts": { + "LAYOUT_ortho_5x12": { + "layout": [ + {"label":"`", "x":0, "y":0}, + {"label":"1", "x":1, "y":0}, + {"label":"2", "x":2, "y":0}, + {"label":"3", "x":3, "y":0}, + {"label":"4", "x":4, "y":0}, + {"label":"5", "x":5, "y":0}, + {"label":"6", "x":6, "y":0}, + {"label":"7", "x":7, "y":0}, + {"label":"8", "x":8, "y":0}, + {"label":"9", "x":9, "y":0}, + {"label":"0", "x":10, "y":0}, + {"label":"Backspace", "x":11, "y":0}, + {"label":"Tab", "x":0, "y":1}, + {"label":"Q", "x":1, "y":1}, + {"label":"W", "x":2, "y":1}, + {"label":"E", "x":3, "y":1}, + {"label":"R", "x":4, "y":1}, + {"label":"T", "x":5, "y":1}, + {"label":"Y", "x":6, "y":1}, + {"label":"U", "x":7, "y":1}, + {"label":"I", "x":8, "y":1}, + {"label":"O", "x":9, "y":1}, + {"label":"P", "x":10, "y":1}, + {"label":"Delete", "x":11, "y":1}, + {"label":"Esc", "x":0, "y":2}, + {"label":"A", "x":1, "y":2}, + {"label":"S", "x":2, "y":2}, + {"label":"D", "x":3, "y":2}, + {"label":"F", "x":4, "y":2}, + {"label":"G", "x":5, "y":2}, + {"label":"H", "x":6, "y":2}, + {"label":"J", "x":7, "y":2}, + {"label":"K", "x":8, "y":2}, + {"label":"L", "x":9, "y":2}, + {"label":";", "x":10, "y":2}, + {"label":"'", "x":11, "y":2}, + {"label":"Shift", "x":0, "y":3}, + {"label":"Z", "x":1, "y":3}, + {"label":"X", "x":2, "y":3}, + {"label":"C", "x":3, "y":3}, + {"label":"V", "x":4, "y":3}, + {"label":"B", "x":5, "y":3}, + {"label":"N", "x":6, "y":3}, + {"label":"M", "x":7, "y":3}, + {"label":",", "x":8, "y":3}, + {"label":".", "x":9, "y":3}, + {"label":"/", "x":10, "y":3}, + {"label":"Enter", "x":11, "y":3}, + {"label":"Fn", "x":0, "y":4}, + {"label":"Ctrl", "x":1, "y":4}, + {"label":"Alt", "x":2, "y":4}, + {"label":"Meta", "x":3, "y":4}, + {"label":"Lower", "x":4, "y":4}, + {"label":"Space", "x":5, "y":4}, + {"label":"Space", "x":6, "y":4}, + {"label":"Raise", "x":7, "y":4}, + {"label":"Left", "x":8, "y":4}, + {"label":"Down", "x":9, "y":4}, + {"label":"Right", "x":10, "y":4}, + {"label":"up", "x":11, "y":4} + ] + } + } +} diff --git a/keyboards/handwired/ortho60/keymaps/default/keymap.c b/keyboards/handwired/ortho60/keymaps/default/keymap.c new file mode 100644 index 0000000000..8617b6341a --- /dev/null +++ b/keyboards/handwired/ortho60/keymaps/default/keymap.c @@ -0,0 +1,98 @@ +/* +Copyright 2012,2013 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ +#include QMK_KEYBOARD_H + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BASE 0 +#define _RAISE 1 +#define _LOWER 2 + +enum custom_keycodes { + QWERTY = SAFE_RANGE, + LOWER, + RAISE +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Tab | Q | W | E | R | T | Y | U | I | O | P | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Esc | A | S | D | F | G | H | J | K | L | ; | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| Z | X | C | V | B | N | M | , | . | / |Enter | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Brite| Ctrl | Alt | GUI |Lower | Space |Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_BASE] = LAYOUT_ortho_5x12( \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, \ + KC_ESC, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_ENT, \ + BL_TOGG, KC_LCTL, KC_LALT, KC_LGUI, LOWER, KC_SPC, KC_SPC, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT \ +), +/* Lower + * ,-----------------------------------------------------------------------------------. + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Bksp | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | ~ | ! | @ | # | $ | % | ^ | & | * | ( | ) | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | _ | + | { | } | | | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO ~ |ISO | | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = LAYOUT_ortho_5x12( \ + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_BSPC, \ + KC_TILD, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DEL, \ + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, KC_PIPE, \ + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12,S(KC_NUHS),S(KC_NUBS),KC_HOME, KC_END, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \ +), + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | ` | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Del | F1 | F2 | F3 | F4 | F5 | F6 | - | = | [ | ] | \ | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | F7 | F8 | F9 | F10 | F11 | F12 |ISO # |ISO / | | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | Next | Vol- | Vol+ | Play | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = LAYOUT_ortho_5x12( \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_BSPC, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DEL, \ + KC_DEL, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, KC_BSLS, \ + _______, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_NUHS, KC_NUBS, KC_PGUP, KC_PGDN, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, KC_MNXT, KC_VOLD, KC_VOLU, KC_MPLY \ +) +}; diff --git a/keyboards/handwired/ortho60/ld/MKL26Z64.ld b/keyboards/handwired/ortho60/ld/MKL26Z64.ld new file mode 100644 index 0000000000..c4ca8b874c --- /dev/null +++ b/keyboards/handwired/ortho60/ld/MKL26Z64.ld @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2013-2016 Fabio Utzig, http://fabioutzig.com + * (C) 2016 flabbergast <s3+flabbergast@sdfeu.org> + * + * Permission is hereby granted, free of charge, to any person obtaining + * a copy of this software and associated documentation files (the "Software"), + * to deal in the Software without restriction, including without limitation + * the rights to use, copy, modify, merge, publish, distribute, sublicense, + * and/or sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS + * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ + +/* + * KL26Z64 memory setup. + */ +MEMORY +{ + flash0 : org = 0x00000000, len = 0x100 + flash1 : org = 0x00000400, len = 0x10 + flash2 : org = 0x00000410, len = 62k - 0x410 + flash3 : org = 0x0000F800, len = 2k + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x1FFFF800, len = 8k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* Flash region for the configuration bytes.*/ +SECTIONS +{ + .cfmprotect : ALIGN(4) SUBALIGN(4) + { + KEEP(*(.cfmconfig)) + } > flash1 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash2); +REGION_ALIAS("XTORS_FLASH_LMA", flash2); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash2); +REGION_ALIAS("TEXT_FLASH_LMA", flash2); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash2); +REGION_ALIAS("RODATA_FLASH_LMA", flash2); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash2); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash2); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash2); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash2); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +__eeprom_workarea_start__ = ORIGIN(flash3); +__eeprom_workarea_size__ = LENGTH(flash3); +__eeprom_workarea_end__ = __eeprom_workarea_start__ + __eeprom_workarea_size__; + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/handwired/ortho60/ld/STM32F103x8_stm32duino_bootloader.ld b/keyboards/handwired/ortho60/ld/STM32F103x8_stm32duino_bootloader.ld new file mode 100644 index 0000000000..d0688ef601 --- /dev/null +++ b/keyboards/handwired/ortho60/ld/STM32F103x8_stm32duino_bootloader.ld @@ -0,0 +1,88 @@ +/* + ChibiOS - Copyright (C) 2006..2016 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +/* + * ST32F103xB memory setup for use with the maplemini bootloader. + * You will have to + * #define CORTEX_VTOR_INIT 0x5000 + * in your projects chconf.h + */ +MEMORY +{ + flash0 : org = 0x08002000, len = 64k - 0x2000 + flash1 : org = 0x00000000, len = 0 + flash2 : org = 0x00000000, len = 0 + flash3 : org = 0x00000000, len = 0 + flash4 : org = 0x00000000, len = 0 + flash5 : org = 0x00000000, len = 0 + flash6 : org = 0x00000000, len = 0 + flash7 : org = 0x00000000, len = 0 + ram0 : org = 0x20000000, len = 20k + ram1 : org = 0x00000000, len = 0 + ram2 : org = 0x00000000, len = 0 + ram3 : org = 0x00000000, len = 0 + ram4 : org = 0x00000000, len = 0 + ram5 : org = 0x00000000, len = 0 + ram6 : org = 0x00000000, len = 0 + ram7 : org = 0x00000000, len = 0 +} + +/* For each data/text section two region are defined, a virtual region + and a load region (_LMA suffix).*/ + +/* Flash region to be used for exception vectors.*/ +REGION_ALIAS("VECTORS_FLASH", flash0); +REGION_ALIAS("VECTORS_FLASH_LMA", flash0); + +/* Flash region to be used for constructors and destructors.*/ +REGION_ALIAS("XTORS_FLASH", flash0); +REGION_ALIAS("XTORS_FLASH_LMA", flash0); + +/* Flash region to be used for code text.*/ +REGION_ALIAS("TEXT_FLASH", flash0); +REGION_ALIAS("TEXT_FLASH_LMA", flash0); + +/* Flash region to be used for read only data.*/ +REGION_ALIAS("RODATA_FLASH", flash0); +REGION_ALIAS("RODATA_FLASH_LMA", flash0); + +/* Flash region to be used for various.*/ +REGION_ALIAS("VARIOUS_FLASH", flash0); +REGION_ALIAS("VARIOUS_FLASH_LMA", flash0); + +/* Flash region to be used for RAM(n) initialization data.*/ +REGION_ALIAS("RAM_INIT_FLASH_LMA", flash0); + +/* RAM region to be used for Main stack. This stack accommodates the processing + of all exceptions and interrupts.*/ +REGION_ALIAS("MAIN_STACK_RAM", ram0); + +/* RAM region to be used for the process stack. This is the stack used by + the main() function.*/ +REGION_ALIAS("PROCESS_STACK_RAM", ram0); + +/* RAM region to be used for data segment.*/ +REGION_ALIAS("DATA_RAM", ram0); +REGION_ALIAS("DATA_RAM_LMA", flash0); + +/* RAM region to be used for BSS segment.*/ +REGION_ALIAS("BSS_RAM", ram0); + +/* RAM region to be used for the default heap.*/ +REGION_ALIAS("HEAP_RAM", ram0); + +/* Generic rules inclusion.*/ +INCLUDE rules.ld diff --git a/keyboards/handwired/ortho60/led.c b/keyboards/handwired/ortho60/led.c new file mode 100644 index 0000000000..f15baed169 --- /dev/null +++ b/keyboards/handwired/ortho60/led.c @@ -0,0 +1,51 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#include "hal.h" +#include "backlight.h" +#include "led.h" +#include "printf.h" + +void backlight_init_ports(void) { + printf("backlight_init_ports()\n"); + #ifdef BACKLIGHT_ENABLE + palSetPadMode(GPIOA, 8, PAL_MODE_OUTPUT_PUSHPULL); + palSetPad(GPIOA, 8); + #endif +} + +void backlight_set(uint8_t level) { + printf("backlight_set(%d)\n", level); + #ifdef BACKLIGHT_ENABLE + if (level == 0) { + // Turn backlight off + palSetPad(GPIOA, 8); + } else { + // Turn backlight on + palClearPad(GPIOA, 8); + } + #endif +} + +void led_set(uint8_t usb_led) +{ + if (usb_led & (1<<USB_LED_CAPS_LOCK)) { + palClearPad(GPIOC, 13); + } else { + palSetPad(GPIOC, 13); + } +} diff --git a/keyboards/handwired/ortho60/mcuconf.h b/keyboards/handwired/ortho60/mcuconf.h new file mode 100644 index 0000000000..9945e7408d --- /dev/null +++ b/keyboards/handwired/ortho60/mcuconf.h @@ -0,0 +1,209 @@ +/* + ChibiOS - Copyright (C) 2006..2015 Giovanni Di Sirio + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. +*/ + +#ifndef _MCUCONF_H_ +#define _MCUCONF_H_ + +#define STM32F103_MCUCONF + +/* + * STM32F103 drivers configuration. + * The following settings override the default settings present in + * the various device driver implementation headers. + * Note that the settings for each driver only have effect if the whole + * driver is enabled in halconf.h. + * + * IRQ priorities: + * 15...0 Lowest...Highest. + * + * DMA priorities: + * 0...3 Lowest...Highest. + */ + +/* + * HAL driver system settings. + */ +#define STM32_NO_INIT FALSE +#define STM32_HSI_ENABLED TRUE +#define STM32_LSI_ENABLED FALSE +#define STM32_HSE_ENABLED TRUE +#define STM32_LSE_ENABLED FALSE +#define STM32_SW STM32_SW_PLL +#define STM32_PLLSRC STM32_PLLSRC_HSE +#define STM32_PLLXTPRE STM32_PLLXTPRE_DIV1 +#define STM32_PLLMUL_VALUE 9 +#define STM32_HPRE STM32_HPRE_DIV1 +#define STM32_PPRE1 STM32_PPRE1_DIV2 +#define STM32_PPRE2 STM32_PPRE2_DIV2 +#define STM32_ADCPRE STM32_ADCPRE_DIV4 +#define STM32_USB_CLOCK_REQUIRED TRUE +#define STM32_USBPRE STM32_USBPRE_DIV1P5 +#define STM32_MCOSEL STM32_MCOSEL_NOCLOCK +#define STM32_RTCSEL STM32_RTCSEL_HSEDIV +#define STM32_PVD_ENABLE FALSE +#define STM32_PLS STM32_PLS_LEV0 + +/* + * ADC driver system settings. + */ +#define STM32_ADC_USE_ADC1 FALSE +#define STM32_ADC_ADC1_DMA_PRIORITY 2 +#define STM32_ADC_ADC1_IRQ_PRIORITY 6 + +/* + * CAN driver system settings. + */ +#define STM32_CAN_USE_CAN1 FALSE +#define STM32_CAN_CAN1_IRQ_PRIORITY 11 + +/* + * EXT driver system settings. + */ +#define STM32_EXT_EXTI0_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI1_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI2_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI3_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI4_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI5_9_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI10_15_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI16_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI17_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI18_IRQ_PRIORITY 6 +#define STM32_EXT_EXTI19_IRQ_PRIORITY 6 + +/* + * GPT driver system settings. + */ +#define STM32_GPT_USE_TIM1 FALSE +#define STM32_GPT_USE_TIM2 FALSE +#define STM32_GPT_USE_TIM3 FALSE +#define STM32_GPT_USE_TIM4 FALSE +#define STM32_GPT_USE_TIM5 FALSE +#define STM32_GPT_USE_TIM8 FALSE +#define STM32_GPT_TIM1_IRQ_PRIORITY 7 +#define STM32_GPT_TIM2_IRQ_PRIORITY 7 +#define STM32_GPT_TIM3_IRQ_PRIORITY 7 +#define STM32_GPT_TIM4_IRQ_PRIORITY 7 +#define STM32_GPT_TIM5_IRQ_PRIORITY 7 +#define STM32_GPT_TIM8_IRQ_PRIORITY 7 + +/* + * I2C driver system settings. + */ +#define STM32_I2C_USE_I2C1 FALSE +#define STM32_I2C_USE_I2C2 FALSE +#define STM32_I2C_BUSY_TIMEOUT 50 +#define STM32_I2C_I2C1_IRQ_PRIORITY 5 +#define STM32_I2C_I2C2_IRQ_PRIORITY 5 +#define STM32_I2C_I2C1_DMA_PRIORITY 3 +#define STM32_I2C_I2C2_DMA_PRIORITY 3 +#define STM32_I2C_DMA_ERROR_HOOK(i2cp) osalSysHalt("DMA failure") + +/* + * ICU driver system settings. + */ +#define STM32_ICU_USE_TIM1 FALSE +#define STM32_ICU_USE_TIM2 FALSE +#define STM32_ICU_USE_TIM3 FALSE +#define STM32_ICU_USE_TIM4 FALSE +#define STM32_ICU_USE_TIM5 FALSE +#define STM32_ICU_USE_TIM8 FALSE +#define STM32_ICU_TIM1_IRQ_PRIORITY 7 +#define STM32_ICU_TIM2_IRQ_PRIORITY 7 +#define STM32_ICU_TIM3_IRQ_PRIORITY 7 +#define STM32_ICU_TIM4_IRQ_PRIORITY 7 +#define STM32_ICU_TIM5_IRQ_PRIORITY 7 +#define STM32_ICU_TIM8_IRQ_PRIORITY 7 + +/* + * PWM driver system settings. + */ +#define STM32_PWM_USE_ADVANCED FALSE +#define STM32_PWM_USE_TIM1 FALSE +#define STM32_PWM_USE_TIM2 FALSE +#define STM32_PWM_USE_TIM3 FALSE +#define STM32_PWM_USE_TIM4 FALSE +#define STM32_PWM_USE_TIM5 FALSE +#define STM32_PWM_USE_TIM8 FALSE +#define STM32_PWM_TIM1_IRQ_PRIORITY 7 +#define STM32_PWM_TIM2_IRQ_PRIORITY 7 +#define STM32_PWM_TIM3_IRQ_PRIORITY 7 +#define STM32_PWM_TIM4_IRQ_PRIORITY 7 +#define STM32_PWM_TIM5_IRQ_PRIORITY 7 +#define STM32_PWM_TIM8_IRQ_PRIORITY 7 + +/* + * RTC driver system settings. + */ +#define STM32_RTC_IRQ_PRIORITY 15 + +/* + * SERIAL driver system settings. + */ +#define STM32_SERIAL_USE_USART1 FALSE +#define STM32_SERIAL_USE_USART2 FALSE +#define STM32_SERIAL_USE_USART3 FALSE +#define STM32_SERIAL_USE_UART4 FALSE +#define STM32_SERIAL_USE_UART5 FALSE +#define STM32_SERIAL_USART1_PRIORITY 12 +#define STM32_SERIAL_USART2_PRIORITY 12 +#define STM32_SERIAL_USART3_PRIORITY 12 +#define STM32_SERIAL_UART4_PRIORITY 12 +#define STM32_SERIAL_UART5_PRIORITY 12 + +/* + * SPI driver system settings. + */ +#define STM32_SPI_USE_SPI1 FALSE +#define STM32_SPI_USE_SPI2 TRUE +#define STM32_SPI_USE_SPI3 FALSE +#define STM32_SPI_SPI1_DMA_PRIORITY 1 +#define STM32_SPI_SPI2_DMA_PRIORITY 1 +#define STM32_SPI_SPI3_DMA_PRIORITY 1 +#define STM32_SPI_SPI1_IRQ_PRIORITY 10 +#define STM32_SPI_SPI2_IRQ_PRIORITY 10 +#define STM32_SPI_SPI3_IRQ_PRIORITY 10 +#define STM32_SPI_DMA_ERROR_HOOK(spip) osalSysHalt("DMA failure") + +/* + * ST driver system settings. + */ +#define STM32_ST_IRQ_PRIORITY 8 +#define STM32_ST_USE_TIMER 2 + +/* + * UART driver system settings. + */ +#define STM32_UART_USE_USART1 FALSE +#define STM32_UART_USE_USART2 FALSE +#define STM32_UART_USE_USART3 FALSE +#define STM32_UART_USART1_IRQ_PRIORITY 12 +#define STM32_UART_USART2_IRQ_PRIORITY 12 +#define STM32_UART_USART3_IRQ_PRIORITY 12 +#define STM32_UART_USART1_DMA_PRIORITY 0 +#define STM32_UART_USART2_DMA_PRIORITY 0 +#define STM32_UART_USART3_DMA_PRIORITY 0 +#define STM32_UART_DMA_ERROR_HOOK(uartp) osalSysHalt("DMA failure") + +/* + * USB driver system settings. + */ +#define STM32_USB_USE_USB1 TRUE +#define STM32_USB_LOW_POWER_ON_SUSPEND FALSE +#define STM32_USB_USB1_HP_IRQ_PRIORITY 13 +#define STM32_USB_USB1_LP_IRQ_PRIORITY 14 + +#endif /* _MCUCONF_H_ */ diff --git a/keyboards/handwired/ortho60/ortho60.c b/keyboards/handwired/ortho60/ortho60.c new file mode 100644 index 0000000000..32db007b6c --- /dev/null +++ b/keyboards/handwired/ortho60/ortho60.c @@ -0,0 +1,32 @@ + +#include "ortho60.h" + +#include "ch.h" +#include "hal.h" + +#include "underglow.h" +#include "print.h" +#include "debug.h" +#include "util.h" + +/* generic STM32F103C8T6 board */ +#ifdef BOARD_GENERIC_STM32_F103 +#define LED_ON() do { palClearPad(GPIOC, 13) ;} while (0) +#define LED_OFF() do { palSetPad(GPIOC, 13); } while (0) +#define LED_TGL() do { palTogglePad(GPIOC, 13); } while (0) +#endif + +void matrix_init_kb(void){ + /* MOSI pin*/ + palSetPadMode(GPIOB, 15, PAL_MODE_STM32_ALTERNATE_PUSHPULL); + + LED_ON(); + palSetPad(GPIOA, 8); + wait_ms(500); + palClearPad(GPIOA, 8); + LED_OFF(); + + leds_init(); + + +} diff --git a/keyboards/handwired/ortho60/ortho60.h b/keyboards/handwired/ortho60/ortho60.h new file mode 100644 index 0000000000..0f3ae127aa --- /dev/null +++ b/keyboards/handwired/ortho60/ortho60.h @@ -0,0 +1,33 @@ +#pragma once + +#include "quantum.h" + +#define LAYOUT_1x2uC( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \ + k40, k41, k42, k43, k44, k45 , k47, k48, k49, k4a, k4b \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b }, \ + { k40, k41, k42, k43, k44, k45, KC_NO, k47, k48, k49, k4a, k4b }, \ +} + +#define LAYOUT_ortho_5x12( \ + k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, \ + k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, \ + k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b, \ + k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b, \ + k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b \ +) \ +{ \ + { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b }, \ + { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b }, \ + { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b }, \ + { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3a, k3b }, \ + { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4a, k4b }, \ +} diff --git a/keyboards/handwired/ortho60/readme.md b/keyboards/handwired/ortho60/readme.md new file mode 100644 index 0000000000..8db1b7df7d --- /dev/null +++ b/keyboards/handwired/ortho60/readme.md @@ -0,0 +1,3 @@ +# Ortho 60 + +Blue Pill STM32F103C8T6 based 12x5 Ortholinear Board diff --git a/keyboards/handwired/ortho60/rules.mk b/keyboards/handwired/ortho60/rules.mk new file mode 100644 index 0000000000..3f4574473c --- /dev/null +++ b/keyboards/handwired/ortho60/rules.mk @@ -0,0 +1,56 @@ +# project specific files +SRC = led.c \ + underglow.c \ + hsv2rgb.c + +# GENERIC STM32F103C8T6 board - stm32duino bootloader +OPT_DEFS = -DCORTEX_VTOR_INIT=0x2000 +MCU_LDSCRIPT = STM32F103x8_stm32duino_bootloader +BOARD = GENERIC_STM32_F103 + +# OPT_DEFS = +# MCU_LDSCRIPT = STM32F103x8 +# BOARD = GENERIC_STM32_F103 + +## chip/board settings +# the next two should match the directories in +# <chibios>/os/hal/ports/$(MCU_FAMILY)/$(MCU_SERIES) +MCU_FAMILY = STM32 +MCU_SERIES = STM32F1xx +# linker script to use +# it should exist either in <chibios>/os/common/ports/ARMCMx/compilers/GCC/ld/ +# or <this_dir>/ld/ +# startup code to use +# is should exist in <chibios>/os/common/ports/ARMCMx/compilers/GCC/mk/ +MCU_STARTUP = stm32f1xx +# it should exist either in <chibios>/os/hal/boards/ +# or <this_dir>/boards +# Cortex version +# Teensy LC is cortex-m0; Teensy 3.x are cortex-m4 +MCU = cortex-m3 +# ARM version, CORTEX-M0/M1 are 6, CORTEX-M3/M4/M7 are 7 +ARMV = 7 +# If you want to be able to jump to bootloader from firmware on STM32 MCUs, +# set the correct BOOTLOADER_ADDRESS. Either set it here, or define it in +# ./bootloader_defs.h or in ./boards/<FOO>/bootloader_defs.h (if you have +# a custom board definition that you plan to reuse). +# If you're not setting it here, leave it commented out. +# It is chip dependent, the correct number can be looked up here (page 175): +# http://www.st.com/web/en/resource/technical/document/application_note/CD00167594.pdf +# This also requires a patch to chibios: +# <tmk_dir>/tmk_core/tool/chibios/ch-bootloader-jump.patch +#STM32_BOOTLOADER_ADDRESS = 0x1FFFC800 + + +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover +BACKLIGHT_ENABLE = yes + +LAYOUTS = ortho_5x12 + +DEFAULT_FOLDER = handwired/ortho60 diff --git a/keyboards/handwired/ortho60/underglow.c b/keyboards/handwired/ortho60/underglow.c new file mode 100644 index 0000000000..1383af1898 --- /dev/null +++ b/keyboards/handwired/ortho60/underglow.c @@ -0,0 +1,157 @@ +#include "ch.h" +#include "hal.h" + +#include "hsv2rgb.h" +#include "underglow.h" + +#define BYTES_FOR_LED_BYTE 4 +#define NB_COLORS 3 +#define BYTES_FOR_LED BYTES_FOR_LED_BYTE*NB_COLORS +#define DATA_SIZE BYTES_FOR_LED*NB_LEDS +#define RESET_SIZE 200 +#define PREAMBLE_SIZE 4 + +// Define the spi your LEDs are plugged to here +#define LEDS_SPI SPID2 +// Define the number of LEDs you wish to control in your LED strip +#define NB_LEDS 8 + +#define LED_SPIRAL 1 + +static uint8_t txbuf[PREAMBLE_SIZE + DATA_SIZE + RESET_SIZE]; +static uint8_t get_protocol_eq(uint8_t data, int pos); + +/* + * This lib is meant to be used asynchronously, thus the colors contained in + * the txbuf will be sent in loop, so that the colors are always the ones you + * put in the table (the user thus have less to worry about) + * + * Since the data are sent via DMA, and the call to spiSend is a blocking one, + * the processor ressources are not used to much, if you see your program being + * too slow, simply add a: + * chThdSleepMilliseconds(x); + * after the spiSend, where you increment x untill you are satisfied with your + * program speed, another trick may be to lower this thread priority : your call + */ +static THD_WORKING_AREA(LEDS_THREAD_WA, 128); +static THD_FUNCTION(ledsThread, arg) { + (void) arg; + while(1){ + spiSend(&LEDS_SPI, PREAMBLE_SIZE + DATA_SIZE + RESET_SIZE, txbuf); + } +} + +#if LED_SPIRAL +/* + * 'Led spiral' is a simple demo in which we put all the leds to the same + * color, where this color does all the hsv circle in loop. + * If you want to launch the thread that will chage the led colors to the + * appropriate value, simply set LED_SPIRAL to 1. + */ +static THD_WORKING_AREA(HSVTRANS_WA, 128); +static THD_FUNCTION(hsv_transThread, arg){ + (void) arg; + hsv_color color = {0, 255, 127}; + while(1){ + color.h += 1; + color.h %= 256; + set_leds_color_hsv(color); + chThdSleepMilliseconds(50); + } +} +#endif + +static const SPIConfig spicfg = { + NULL, + GPIOB, + 15, + SPI_CR1_BR_1|SPI_CR1_BR_0 // baudrate : fpclk / 8 => 1tick is 0.32us +}; + +/* + * Function used to initialize the driver. + * + * Starts by shutting off all the LEDs. + * Then gets access on the LED_SPI driver. + * May eventually launch an animation on the LEDs (e.g. a thread setting the + * txbuff values) + */ +void leds_init(void){ + for(int i = 0; i < RESET_SIZE; i++) + txbuf[DATA_SIZE+i] = 0x00; + for (int i=0; i<PREAMBLE_SIZE; i++) + txbuf[i] = 0x00; + spiAcquireBus(&LEDS_SPI); /* Acquire ownership of the bus. */ + spiStart(&LEDS_SPI, &spicfg); /* Setup transfer parameters. */ + spiSelect(&LEDS_SPI); /* Slave Select assertion. */ + chThdCreateStatic(LEDS_THREAD_WA, sizeof(LEDS_THREAD_WA),NORMALPRIO, ledsThread, NULL); +#if LED_SPIRAL + chThdCreateStatic(HSVTRANS_WA, sizeof(HSVTRANS_WA), + NORMALPRIO, hsv_transThread, NULL); +#endif +} + +/* + * As the trick here is to use the SPI to send a huge pattern of 0 and 1 to + * the ws2812b protocol, we use this helper function to translate bytes into + * 0s and 1s for the LED (with the appropriate timing). + */ +static uint8_t get_protocol_eq(uint8_t data, int pos){ + uint8_t eq = 0; + if (data & (1 << (2*(3-pos)))) + eq = 0b1110; + else + eq = 0b1000; + if (data & (2 << (2*(3-pos)))) + eq += 0b11100000; + else + eq += 0b10000000; + return eq; +} + +/* + * If you want to set a LED's color in the HSV color space, simply call this + * function with a hsv_color containing the desired color and the index of the + * led on the LED strip (starting from 0, the first one being the closest the + * first plugged to the board) + * + * Only set the color of the LEDs through the functions given by this API + * (unless you really know what you are doing) + */ +void set_led_color_hsv(hsv_color color, int pos){ + set_led_color_rgb(hsv2rgb(color), pos); +} + +/* + * If you want to set a LED's color in the RGB color space, simply call this + * function with a hsv_color containing the desired color and the index of the + * led on the LED strip (starting from 0, the first one being the closest the + * first plugged to the board) + * + * Only set the color of the LEDs through the functions given by this API + * (unless you really know what you are doing) + */ +void set_led_color_rgb(rgb_color color, int pos){ + for(int j = 0; j < 4; j++) + txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + j] = get_protocol_eq(color.g, j); + for(int j = 0; j < 4; j++) + txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + BYTES_FOR_LED_BYTE+j] = get_protocol_eq(color.r, j); + for(int j = 0; j < 4; j++) + txbuf[PREAMBLE_SIZE + BYTES_FOR_LED*pos + BYTES_FOR_LED_BYTE*2+j] = get_protocol_eq(color.b, j); +} + +/* + * Same as the two above, but sets all the LEDs in the LED strip (HSV) + */ +void set_leds_color_hsv(hsv_color color){ + for(int i = 0; i < NB_LEDS; i++) + set_led_color_hsv(color, i); +} + +/* + * Same as the two above, but sets all the LEDs in the LED strip (RGB) + */ +void set_leds_color_rgb(rgb_color color){ + for(int i = 0; i < NB_LEDS; i++) + set_led_color_rgb(color, i); +}
\ No newline at end of file diff --git a/keyboards/handwired/ortho60/underglow.h b/keyboards/handwired/ortho60/underglow.h new file mode 100644 index 0000000000..ff11952791 --- /dev/null +++ b/keyboards/handwired/ortho60/underglow.h @@ -0,0 +1,10 @@ +#pragma once + +#include "hsv2rgb.h" + +void set_leds_color_hsv(hsv_color color); +void set_leds_color_rgb(rgb_color color); +void set_led_color_hsv(hsv_color color, int pos); +void set_led_color_rgb(rgb_color color, int pos); + +void leds_init(void); |