diff options
Diffstat (limited to 'converter/next_usb/config.h')
| -rw-r--r-- | converter/next_usb/config.h | 188 |
1 files changed, 188 insertions, 0 deletions
diff --git a/converter/next_usb/config.h b/converter/next_usb/config.h new file mode 100644 index 0000000000..cd80b5af1b --- /dev/null +++ b/converter/next_usb/config.h @@ -0,0 +1,188 @@ +/* +NeXT non-ADB Keyboard USB Converter + +Copyright 2013, Benjamin Gould (bgould@github.com) + +Based on: +TMK firmware code Copyright 2011,2012 Jun WAKO <wakojun@gmail.com> +Arduino code by "Ladyada" Limor Fried (http://ladyada.net/, http://adafruit.com/), released under BSD license + +Timing reference thanks to http://m0115.web.fc2.com/ (dead link), http://cfile7.uf.tistory.com/image/14448E464F410BF22380BB +Pinouts thanks to http://www.68k.org/~degs/nextkeyboard.html +Keycodes from http://ftp.netbsd.org/pub/NetBSD/NetBSD-release-6/src/sys/arch/next68k/dev/ + +This software is licensed with a Modified BSD License. +All of this is supposed to be Free Software, Open Source, DFSG-free, +GPL-compatible, and OK to use in both free and proprietary applications. +Additions and corrections to this file are welcome. + +Redistribution and use in source and binary forms, with or without +modification, are permitted provided that the following conditions are met: + +* Redistributions of source code must retain the above copyright + notice, this list of conditions and the following disclaimer. + +* Redistributions in binary form must reproduce the above copyright + notice, this list of conditions and the following disclaimer in + the documentation and/or other materials provided with the + distribution. + +* Neither the name of the copyright holders nor the names of + contributors may be used to endorse or promote products derived + from this software without specific prior written permission. + +THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE +LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +POSSIBILITY OF SUCH DAMAGE. + +*/ + +#define VENDOR_ID 0xBCBC +#define PRODUCT_ID 0xBCBC +#define DEVICE_VER 0x0500 +#define MANUFACTURER t.m.k. +#define PRODUCT NeXT Keyboard to USB converter +#define DESCRIPTION USB converter for NeXT non-ADB Keyboard + +/* matrix size */ +#define MATRIX_ROWS 12 // keycode bit: 3-0 +#define MATRIX_COLS 8 // keycode bit: 6-4 + +//#define DEBUG_ON_INIT 1 + +//#define TEENSY_CONFIG 1 +#define PRO_MICRO_CONFIG 1 +//#define TMK_CONFIG 1 + +// comment out if you don't want the keyboard's LEDs to flash upon initialization +#define NEXT_KBD_INIT_FLASH_LEDS + +//============= Start of Arduino Pro Micro Configuration ============== +#ifdef PRO_MICRO_CONFIG + +// this is the debugging LED that flashes when a key is being pressed +// comment out in order to disable debugging LED +#define NEXT_KBD_LED1_PORT PORTD +#define NEXT_KBD_LED1_PIN PIND +#define NEXT_KBD_LED1_DDR DDRD +#define NEXT_KBD_LED1_BIT 5 + +#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT); +#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT); + +// reserved for future use +#define NEXT_KBD_LED2_PORT PORTB +#define NEXT_KBD_LED2_PIN PINB +#define NEXT_KBD_LED2_DDR DDRB +#define NEXT_KBD_LED2_BIT 6 + +#define NEXT_KBD_LED2_ON NEXT_KBD_LED2_PORT &= ~(1<<NEXT_KBD_LED2_BIT); +#define NEXT_KBD_LED2_OFF NEXT_KBD_LED2_PORT |= (1<<NEXT_KBD_LED2_BIT); + +// corresponds to the Keyboard In wire on the NeXT connector +// (red wire in NeXT connector) - pin 2 on the Pro Micro +#define NEXT_KBD_OUT_PORT PORTD +#define NEXT_KBD_OUT_PIN PIND +#define NEXT_KBD_OUT_DDR DDRD +#define NEXT_KBD_OUT_BIT 1 + +// corresponds to the Keyboard Out wire on the NeXT connector +// (orange wire in NeXT connector) - pin 3 on the Pro Micro +#define NEXT_KBD_IN_PORT PORTD +#define NEXT_KBD_IN_PIN PIND +#define NEXT_KBD_IN_DDR DDRD +#define NEXT_KBD_IN_BIT 0 + +// this pin is an input for the power key on the NeXT keyboard +// as the keyboard is powered on this should be normally high; +// if it is pulled low it means the power button is being preseed +// (yellow wire in NeXT connector) - pin 4 on the Pro Micro +#define NEXT_KBD_PWR_PORT PORTD +#define NEXT_KBD_PWR_PIN PIND +#define NEXT_KBD_PWR_DDR DDRD +#define NEXT_KBD_PWR_BIT 4 + +#endif +//============== End of Arduino Pro Micro Configuration =============== + + +//================ Start of Teensy 2.0 Configuration ================= +#ifdef TEENSY_CONFIG + +// this is the debugging LED that flashes when a key is being pressed +// comment out in order to disable debugging LED +#define NEXT_KBD_LED_PORT PORTD +#define NEXT_KBD_LED_PIN PIND +#define NEXT_KBD_LED_DDR DDRD +#define NEXT_KBD_LED_BIT 6 + +#define NEXT_KBD_LED_ON NEXT_KBD_LED_PORT |= (1<<NEXT_KBD_LED_BIT); +#define NEXT_KBD_LED_OFF NEXT_KBD_LED_PORT &= ~(1<<NEXT_KBD_LED_BIT); + +// corresponds to the Keyboard In wire on the NeXT connector +// (red wire in NeXT connector) +#define NEXT_KBD_OUT_PORT PORTB +#define NEXT_KBD_OUT_PIN PINB +#define NEXT_KBD_OUT_DDR DDRB +#define NEXT_KBD_OUT_BIT 1 + +// corresponds to the Keyboard Out wire on the NeXT connector +// (orange wire in NeXT connector) +#define NEXT_KBD_IN_PORT PORTB +#define NEXT_KBD_IN_PIN PINB +#define NEXT_KBD_IN_DDR DDRB +#define NEXT_KBD_IN_BIT 0 + +#endif +//================= End of Teensy 2.0 Configuration ================== + + +//================ Start of TMK converter Configuration ================= +#ifdef TMK_CONFIG + +// this is the debugging LED that flashes when a key is being pressed +// comment out in order to disable debugging LED +#define NEXT_KBD_LED1_PORT PORTD +#define NEXT_KBD_LED1_PIN PIND +#define NEXT_KBD_LED1_DDR DDRD +#define NEXT_KBD_LED1_BIT 6 + +#define NEXT_KBD_LED1_ON NEXT_KBD_LED1_PORT |= (1<<NEXT_KBD_LED1_BIT); +#define NEXT_KBD_LED1_OFF NEXT_KBD_LED1_PORT &= ~(1<<NEXT_KBD_LED1_BIT); + +// corresponds to the Keyboard In wire on the NeXT connector +#define NEXT_KBD_OUT_PORT PORTD +#define NEXT_KBD_OUT_PIN PIND +#define NEXT_KBD_OUT_DDR DDRD +#define NEXT_KBD_OUT_BIT 1 + +// corresponds to the Keyboard Out wire on the NeXT connector +#define NEXT_KBD_IN_PORT PORTD +#define NEXT_KBD_IN_PIN PIND +#define NEXT_KBD_IN_DDR DDRD +#define NEXT_KBD_IN_BIT 0 + +// this pin is an input for the power key on the NeXT keyboard +// as the keyboard is powered on this should be normally high; +// if it is pulled low it means the power button is being preseed +#define NEXT_KBD_PWR_PORT PORTD +#define NEXT_KBD_PWR_PIN PIND +#define NEXT_KBD_PWR_DDR DDRD +#define NEXT_KBD_PWR_BIT 4 + +#endif +//================= End of TMK converter Configuration ================== + +/* key combination for command */ +#define IS_COMMAND() ( \ + (keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)))|| \ + (keyboard_report->mods == (MOD_BIT(KC_RALT) | MOD_BIT(KC_RCTL))) \ +) |