diff options
Diffstat (limited to 'converter/serialmouse_usb/Makefile')
| -rw-r--r-- | converter/serialmouse_usb/Makefile | 106 |
1 files changed, 106 insertions, 0 deletions
diff --git a/converter/serialmouse_usb/Makefile b/converter/serialmouse_usb/Makefile new file mode 100644 index 0000000000..34f550b314 --- /dev/null +++ b/converter/serialmouse_usb/Makefile @@ -0,0 +1,106 @@ +# +# Makefile for Teensy +# +# Target file name (without extension). +TARGET = serialmouse_usb + +# Directory common source filess exist +TMK_DIR = ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# project specific files +SRC = keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + + +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +#MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +#EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +#COMMAND_ENABLE = yes # Commands for debug and configuration +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + + +# Serial Mouse Options +# You can choose a mouse protocol and the implementation of +# the underlying serial connection. +# +SERIAL_MOUSE_MICROSOFT_ENABLE = yes # Enable support for Microsoft-compatible mice +#SERIAL_MOUSE_MOUSESYSTEMS_ENABLE = yes # Enable support for Mousesystems-compatible mice +#SERIAL_MOUSE_USE_UART = yes # use hardware UART for serial connection +SERIAL_MOUSE_USE_SOFT = yes # use software serial implementation + +# Optional serial mouse driver features +# Support scrolling while holding the middle mouse button +# (currently only supported for Mousesystems mice): +#OPT_DEFS += -DSERIAL_MOUSE_CENTER_SCROLL + +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TMK_DIR) + +include $(TMK_DIR)/protocol.mk +include $(TMK_DIR)/protocol/lufa.mk +include $(TMK_DIR)/common.mk +include $(TMK_DIR)/rules.mk |