diff options
Diffstat (limited to 'keyboard/atomic_old/Makefile.pjrc')
| -rw-r--r-- | keyboard/atomic_old/Makefile.pjrc | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/keyboard/atomic_old/Makefile.pjrc b/keyboard/atomic_old/Makefile.pjrc new file mode 100644 index 0000000000..9655ff65a9 --- /dev/null +++ b/keyboard/atomic_old/Makefile.pjrc @@ -0,0 +1,116 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = gh60_pjrc + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# project specific files +SRC = keymap_common.c \ + matrix.c \ + led.c + +ifdef KEYMAP + SRC := keymap_$(KEYMAP).c $(SRC) +else + SRC := keymap_poker.c $(SRC) +endif + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +MCU = atmega32u4 +#MCU = at90usb1286 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+5000) +EXTRAKEY_ENABLE = yes # Audio control and System control(+600) +CONSOLE_ENABLE = yes # Console for debug +COMMAND_ENABLE = yes # Commands for debug and configuration +SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover(+500) +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk + +plain: OPT_DEFS += -DKEYMAP_PLAIN +plain: all + +poker: OPT_DEFS += -DKEYMAP_POKER +poker: all + +poker_set: OPT_DEFS += -DKEYMAP_POKER_SET +poker_set: all + +poker_bit: OPT_DEFS += -DKEYMAP_POKER_BIT +poker_bit: all |