diff options
Diffstat (limited to 'keyboard/ergodox_ez/Makefile')
| -rw-r--r-- | keyboard/ergodox_ez/Makefile | 130 |
1 files changed, 0 insertions, 130 deletions
diff --git a/keyboard/ergodox_ez/Makefile b/keyboard/ergodox_ez/Makefile deleted file mode 100644 index 3a07ec254f..0000000000 --- a/keyboard/ergodox_ez/Makefile +++ /dev/null @@ -1,130 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# Target file name (without extension). -TARGET = ergodox_ez - - -# Directory common source filess exist -TOP_DIR = ../.. -TMK_DIR = ../../tmk_core - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# # project specific files -SRC = ergodox_ez.c \ - twimaster.c \ - matrix.c - -ifdef KEYMAP - SRC := keymaps/$(KEYMAP)/keymap.c $(SRC) -else - SRC := keymaps/default/keymap.c $(SRC) -endif - -CONFIG_H = config.h - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=512 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -# CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = yes # Commands for debug and configuration -CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDox EZ -SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# MIDI_ENABLE = yes # MIDI controls -# UNICODE_ENABLE = yes # Unicode - -# If you want to have your own config_user.h, you can just put it in -# your keymap directory. Anything you set there will take precedence -# over the global config.h. -ifneq ("$(wildcard keymaps/$(KEYMAP)/config_user.h)","") -CONFIG_USER_H = keymaps/$(KEYMAP)/config_user.h -endif - -ifdef KEYMAP - -ifeq ("$(wildcard keymaps/$(KEYMAP).c)","") -ifneq ("$(wildcard keymaps/$(KEYMAP)/makefile.mk)","") - include keymaps/$(KEYMAP)/makefile.mk -endif -endif -endif - - -# Optimize size but this may cause error "relocation truncated to fit" -#EXTRALDFLAGS = -Wl,--relax - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TOP_DIR) -VPATH += $(TMK_DIR) - -include $(TOP_DIR)/quantum/quantum.mk - |