summaryrefslogtreecommitdiff
path: root/keyboards/gh60
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/gh60')
-rw-r--r--keyboards/gh60/Makefile74
-rw-r--r--keyboards/gh60/config.h161
-rw-r--r--keyboards/gh60/gh60.c25
-rw-r--r--keyboards/gh60/gh60.h74
-rw-r--r--keyboards/gh60/gh60revc.jpgbin0 -> 1424987 bytes
-rw-r--r--keyboards/gh60/keymaps/default/keymap.c69
-rw-r--r--keyboards/gh60/pinout.txt18
-rw-r--r--keyboards/gh60/readme.md60
8 files changed, 481 insertions, 0 deletions
diff --git a/keyboards/gh60/Makefile b/keyboards/gh60/Makefile
new file mode 100644
index 0000000000..39a9cc0ae1
--- /dev/null
+++ b/keyboards/gh60/Makefile
@@ -0,0 +1,74 @@
+
+
+# MCU name
+#MCU = at90usb1287
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# comment out to disable the options.
+#
+BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+# CONSOLE_ENABLE ?= yes # Console for debug(+400)
+# COMMAND_ENABLE ?= yes # Commands for debug and configuration
+KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+# SLEEP_LED_ENABLE ?= yes # Breathing sleep LED during USB suspend
+NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+# BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality
+# MIDI_ENABLE ?= YES # MIDI controls
+# UNICODE_ENABLE ?= YES # Unicode
+# BLUETOOTH_ENABLE ?= yes # Enable Bluetooth with the Adafruit EZ-Key HID
+
+
+ifndef QUANTUM_DIR
+ include ../../Makefile
+endif
+
diff --git a/keyboards/gh60/config.h b/keyboards/gh60/config.h
new file mode 100644
index 0000000000..4813c4e786
--- /dev/null
+++ b/keyboards/gh60/config.h
@@ -0,0 +1,161 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER geekhack
+#define PRODUCT GH60
+#define DESCRIPTION t.m.k. keyboard firmware for GH60
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+ #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 }
+// Rev A
+// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 }
+// Rev B/C
+ #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+#define BACKLIGHT_LEVELS 3
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1 H
+//#define MAGIC_KEY_HELP2 SLASH
+//#define MAGIC_KEY_DEBUG D
+//#define MAGIC_KEY_DEBUG_MATRIX X
+//#define MAGIC_KEY_DEBUG_KBD K
+//#define MAGIC_KEY_DEBUG_MOUSE M
+//#define MAGIC_KEY_VERSION V
+//#define MAGIC_KEY_STATUS S
+//#define MAGIC_KEY_CONSOLE C
+//#define MAGIC_KEY_LAYER0_ALT1 ESC
+//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
+//#define MAGIC_KEY_LAYER0 0
+//#define MAGIC_KEY_LAYER1 1
+//#define MAGIC_KEY_LAYER2 2
+//#define MAGIC_KEY_LAYER3 3
+//#define MAGIC_KEY_LAYER4 4
+//#define MAGIC_KEY_LAYER5 5
+//#define MAGIC_KEY_LAYER6 6
+//#define MAGIC_KEY_LAYER7 7
+//#define MAGIC_KEY_LAYER8 8
+//#define MAGIC_KEY_LAYER9 9
+//#define MAGIC_KEY_BOOTLOADER PAUSE
+//#define MAGIC_KEY_LOCK CAPS
+//#define MAGIC_KEY_EEPROM E
+//#define MAGIC_KEY_NKRO N
+//#define MAGIC_KEY_SLEEP_LED Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/gh60/gh60.c b/keyboards/gh60/gh60.c
new file mode 100644
index 0000000000..255d87de99
--- /dev/null
+++ b/keyboards/gh60/gh60.c
@@ -0,0 +1,25 @@
+#include "gh60.h"
+
+void led_set_kb(uint8_t usb_led) {
+ // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here
+
+ if (usb_led & (1<<USB_LED_CAPS_LOCK)) {
+ gh60_caps_led_on();
+ } else {
+ gh60_caps_led_off();
+ }
+
+ // if (usb_led & (1<<USB_LED_NUM_LOCK)) {
+ // gh60_esc_led_on();
+ // } else {
+ // gh60_esc_led_off();
+ // }
+
+ // if (usb_led & (1<<USB_LED_SCROLL_LOCK)) {
+ // gh60_fn_led_on();
+ // } else {
+ // gh60_fn_led_off();
+ // }
+
+ led_set_user(usb_led);
+}
diff --git a/keyboards/gh60/gh60.h b/keyboards/gh60/gh60.h
new file mode 100644
index 0000000000..ca30562a44
--- /dev/null
+++ b/keyboards/gh60/gh60.h
@@ -0,0 +1,74 @@
+#ifndef GH60_H
+#define GH60_H
+
+#include "quantum.h"
+#include "led.h"
+
+/* GH60 LEDs
+ * GPIO pads
+ * 0 F7 WASD LEDs
+ * 1 F6 ESC LED
+ * 2 F5 FN LED
+ * 3 F4 POKER Arrow LEDs
+ * B2 Capslock LED
+ * B0 not connected
+ */
+inline void gh60_caps_led_on(void) { DDRB |= (1<<2); PORTB &= ~(1<<2); }
+inline void gh60_poker_leds_on(void) { DDRF |= (1<<4); PORTF &= ~(1<<4); }
+inline void gh60_fn_led_on(void) { DDRF |= (1<<5); PORTF &= ~(1<<5); }
+inline void gh60_esc_led_on(void) { DDRF |= (1<<6); PORTF &= ~(1<<6); }
+inline void gh60_wasd_leds_on(void) { DDRF |= (1<<7); PORTF &= ~(1<<7); }
+
+inline void gh60_caps_led_off(void) { DDRB &= ~(1<<2); PORTB &= ~(1<<2); }
+inline void gh60_poker_leds_off(void) { DDRF &= ~(1<<4); PORTF &= ~(1<<4); }
+inline void gh60_fn_led_off(void) { DDRF &= ~(1<<5); PORTF &= ~(1<<5); }
+inline void gh60_esc_led_off(void) { DDRF &= ~(1<<6); PORTF &= ~(1<<6); }
+inline void gh60_wasd_leds_off(void) { DDRF &= ~(1<<7); PORTF &= ~(1<<7); }
+
+/* GH60 keymap definition macro
+ * K2C, K31 and K3C are extra keys for ISO
+ */
+#define KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
+ K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+ K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \
+) { \
+ { KC_##K00, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D }, \
+ { KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_NO, KC_##K45, KC_NO, KC_NO, KC_NO, KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D } \
+}
+
+/* ANSI valiant. No extra keys for ISO */
+#define KEYMAP_ANSI( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \
+ K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, \
+ K40, K41, K42, K45, K4A, K4B, K4C, K4D \
+) KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \
+ K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, NO, K3D, \
+ K40, K41, K42, K45, NO, K4A, K4B, K4C, K4D \
+)
+
+#define KEYMAP_HHKB( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, K49,\
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2D, \
+ K30, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3D, K3C, \
+ K40, K41, K42, K45, K4A, K4B, K4C, K4D \
+) KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, NO, K2D, \
+ K30, NO, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+ K40, K41, K42, K45, K49, K4A, K4B, K4C, K4D \
+)
+
+#endif
diff --git a/keyboards/gh60/gh60revc.jpg b/keyboards/gh60/gh60revc.jpg
new file mode 100644
index 0000000000..6c88ad2442
--- /dev/null
+++ b/keyboards/gh60/gh60revc.jpg
Binary files differ
diff --git a/keyboards/gh60/keymaps/default/keymap.c b/keyboards/gh60/keymaps/default/keymap.c
new file mode 100644
index 0000000000..3622be41b8
--- /dev/null
+++ b/keyboards/gh60/keymaps/default/keymap.c
@@ -0,0 +1,69 @@
+#include "gh60.h"
+#include "action_layer.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ /* 0: qwerty */
+ KEYMAP(
+ ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, GRV, \
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSPC, \
+ CAPS,A, S, D, F, G, H, J, K, L, SCLN,QUOT,NO, ENT, \
+ LSFT,FN1, Z, X, C, V, B, N, M, COMM,DOT, SLSH,FN0, RSFT, \
+ LCTL,LGUI,LALT, SPC, BSLS,RALT,RGUI,APP, RCTL),
+ /* 1: fn */
+ KEYMAP(
+ ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, TRNS, \
+ TRNS,TRNS,UP, TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,LEFT,DOWN,RGHT,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,TRNS,TRNS,TRNS),
+ /* 2: arrows */
+ KEYMAP(
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS, \
+ TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,TRNS,UP, \
+ TRNS,TRNS,TRNS, TRNS, TRNS,TRNS,LEFT,DOWN,RGHT),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+ [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay
+ [1] = ACTION_LAYER_TOGGLE(2), // toggle arrow overlay
+};
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ // MACRODOWN only works in this function
+ switch(id) {
+ case 0:
+ if (record->event.pressed) {
+ register_code(KC_RSFT);
+ } else {
+ unregister_code(KC_RSFT);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
+
+void matrix_scan_user(void) {
+
+//Layer LED indicators
+ uint32_t layer = layer_state;
+
+ if (layer & (1<<1)) {
+ gh60_wasd_leds_on();
+ gh60_fn_led_on();
+ } else {
+ gh60_wasd_leds_off();
+ gh60_fn_led_off();
+ }
+
+ if (layer & (1<<2)) {
+ gh60_poker_leds_on();
+ gh60_esc_led_on();
+ } else {
+ gh60_poker_leds_off();
+ gh60_esc_led_off();
+ }
+
+};
diff --git a/keyboards/gh60/pinout.txt b/keyboards/gh60/pinout.txt
new file mode 100644
index 0000000000..3787f938e7
--- /dev/null
+++ b/keyboards/gh60/pinout.txt
@@ -0,0 +1,18 @@
+ /* Column pin configuration
+ * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13
+ * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C)
+ */
+
+ /* Row pin configuration
+ * row: 0 1 2 3 4
+ * pin: D0 D1 D2 D3 D5
+ */
+
+ GPIO pads
+ 0 F7 WASD LEDs
+ 1 F6 ESC LED
+ 2 F5 FN LED
+ 3 F4 POKER Arrow LEDs
+
+ B2 Capslock LED
+ B0 not connected \ No newline at end of file
diff --git a/keyboards/gh60/readme.md b/keyboards/gh60/readme.md
new file mode 100644
index 0000000000..92302d507c
--- /dev/null
+++ b/keyboards/gh60/readme.md
@@ -0,0 +1,60 @@
+## gh60 Rev C keyboard firmware
+
+![gh60 Rev C PCB](gh60revc.jpg)
+
+ /* Column pin configuration
+ * col: 0 1 2 3 4 5 6 7 8 9 10 11 12 13
+ * pin: F0 F1 E6 C7 C6 B6 D4 B1 B7 B5 B4 D7 D6 B3 (Rev.C)
+ */
+
+ /* Row pin configuration
+ * row: 0 1 2 3 4
+ * pin: D0 D1 D2 D3 D5
+ */
+
+ GPIO pads
+ 0 F7 WASD LEDs
+ 1 F6 ESC LED
+ 2 F5 FN LED
+ 3 F4 POKER Arrow LEDs
+
+ B2 Capslock LED
+ B0 not connected
+
+Functions to controls LED clusters
+
+ gh60_caps_led_on()
+ gh60_poker_leds_on()
+ gh60_fn_led_on()
+ gh60_esc_led_on()
+ gh60_wasd_leds_on()
+
+ gh60_caps_led_off()
+ gh60_poker_leds_off()
+ gh60_fn_led_off()
+ gh60_esc_led_off()
+ gh60_wasd_leds_off()
+
+======================
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/gh60_rev_c folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files.
+
+To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like:
+```
+$ make KEYMAP=[default|jack|<name>]
+```
+Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder.
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-30 11:53:08 +0000