diff options
Diffstat (limited to 'keyboards/handwired/woodpad/rules.mk')
| -rw-r--r-- | keyboards/handwired/woodpad/rules.mk | 61 |
1 files changed, 8 insertions, 53 deletions
diff --git a/keyboards/handwired/woodpad/rules.mk b/keyboards/handwired/woodpad/rules.mk index 4bdc561a63..7725131978 100644 --- a/keyboards/handwired/woodpad/rules.mk +++ b/keyboards/handwired/woodpad/rules.mk @@ -1,49 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Bootloader -# This definition is optional, and if your keyboard supports multiple bootloaders of -# different sizes, comment this out, and the correct address will be loaded -# automatically (+60). See bootloader.mk for all options. +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = caterina -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Build Options # change yes to no to disable # @@ -63,15 +30,3 @@ BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE ?= no # Audio output on port C6 FAUXCLICKY_ENABLE ?= no # Use buzzer to emulate clicky switches RGBLIGHT_ENABLE ?= no - -#avrdude: build -# ls /dev/tty* > /tmp/1; \ -# echo "Reset your Pro Micro now"; \ -# while [ -z $$USB ]; do \ -# sleep 1; \ -# ls /dev/tty* > /tmp/2; \ -# USB=`diff /tmp/1 /tmp/2 | $(GREP) -o '/dev/tty.*'`; \ -# done; \ -# avrdude -p $(MCU) -c avr109 -P $$USB -U flash:w:$(BUILD_DIR)/$(TARGET).hex -# -#.PHONY: avrdude |