diff options
Diffstat (limited to 'keyboards/wilba_tech/wt60_a')
| -rw-r--r-- | keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk | 2 | ||||
| -rw-r--r-- | keyboards/wilba_tech/wt60_a/rules.mk | 61 |
2 files changed, 16 insertions, 47 deletions
diff --git a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk index 8834bf0c8e..4880a57bec 100644 --- a/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk +++ b/keyboards/wilba_tech/wt60_a/keymaps/via/rules.mk @@ -1,2 +1,2 @@ RAW_ENABLE = yes -DYNAMIC_KEYMAP_ENABLE = yes
\ No newline at end of file +DYNAMIC_KEYMAP_ENABLE = yes diff --git a/keyboards/wilba_tech/wt60_a/rules.mk b/keyboards/wilba_tech/wt60_a/rules.mk index 4f702fab49..111c94ee80 100644 --- a/keyboards/wilba_tech/wt60_a/rules.mk +++ b/keyboards/wilba_tech/wt60_a/rules.mk @@ -1,54 +1,16 @@ -# project specific files -SRC = drivers/issi/is31fl3736.c \ - drivers/avr/i2c_master.c \ - quantum/color.c \ - keyboards/wilba_tech/wt_mono_backlight.c \ - keyboards/wilba_tech/wt_main.c - # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # change yes to no to disable # @@ -67,3 +29,10 @@ UNICODE_ENABLE = no # Unicode BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches + +# project specific files +SRC = drivers/issi/is31fl3736.c \ + drivers/avr/i2c_master.c \ + quantum/color.c \ + keyboards/wilba_tech/wt_mono_backlight.c \ + keyboards/wilba_tech/wt_main.c |