diff options
Diffstat (limited to 'keyboards')
21 files changed, 686 insertions, 0 deletions
diff --git a/keyboards/handwired/minorca/Makefile b/keyboards/handwired/minorca/Makefile new file mode 100644 index 0000000000..155c1f9a29 --- /dev/null +++ b/keyboards/handwired/minorca/Makefile @@ -0,0 +1,71 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=512 + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +NKRO_ENABLE ?= yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +AUDIO_ENABLE ?= no # Audio output on port C6 +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE ?= yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../Makefile +endif
\ No newline at end of file diff --git a/keyboards/handwired/minorca/config.h b/keyboards/handwired/minorca/config.h new file mode 100644 index 0000000000..4cdafcbd2e --- /dev/null +++ b/keyboards/handwired/minorca/config.h @@ -0,0 +1,80 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6660 +#define DEVICE_VER 0x0001 +#define MANUFACTURER ME +#define PRODUCT MinOrca +#define DESCRIPTION Tiny Whale + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 12 + +/* MinOrca PCB default pin-out */ +#define MATRIX_COL_PINS { D4, D6, D7, B4, B5, B6, F7, F6, F5, F4, F1, F0 } +#define MATRIX_ROW_PINS { B0, B1, B2, B3 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/handwired/minorca/keymaps/default/Makefile b/keyboards/handwired/minorca/keymaps/default/Makefile new file mode 100644 index 0000000000..a573488a5e --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../../Makefile +endif diff --git a/keyboards/handwired/minorca/keymaps/default/config.h b/keyboards/handwired/minorca/keymaps/default/config.h new file mode 100644 index 0000000000..bf40376c19 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/config.h @@ -0,0 +1,12 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +/* bootmagic salt key */ +#define BOOTMAGIC_KEY_SALT KC_ESC + +/* skip bootmagic and eeconfig */ +#define BOOTMAGIC_KEY_SKIP KC_SPACE + +#endif diff --git a/keyboards/handwired/minorca/keymaps/default/keymap.c b/keyboards/handwired/minorca/keymaps/default/keymap.c new file mode 100644 index 0000000000..a55d578e44 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/keymap.c @@ -0,0 +1,44 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "minorca.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = { /* Base */ + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC }, + {KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, XXXXXXX, KC_ENT }, + {KC_LCTRL,XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_QUOT, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, KC_SPC, XXXXXXX, XXXXXXX, KC_SPC, XXXXXXX, KC_DOT, KC_SLSH, KC_NO } + }, + [1] = { /* First */ + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DELT }, + {KC_TAB, KC_MPRV, KC_MPLY, KC_MNXT, KC_PGUP, KC_HOME, KC_MINS, KC_EQL, KC_LBRC, KC_RBRC, XXXXXXX, KC_LGUI }, + {KC_LCTRL,XXXXXXX, KC_Z, KC_X, KC_C, KC_PGDN, KC_END, KC_L, KC_SCLN, KC_UP, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO } + }, + [2] = { /* Second */ + {KC_ESC, KC_EXLM, KC_AT, KC_HASH, KC_DLR, KC_PERC, KC_CIRC, KC_AMPR, KC_ASTR, KC_LPRN, KC_RPRN, KC_DELT }, + {KC_TAB, KC_MUTE, KC_VOLD, KC_VOLU, KC_TILD, KC_PIPE, KC_UNDS, KC_PLUS, KC_LCBR, KC_RCBR, XXXXXXX, KC_ENT }, + {KC_CAPS, XXXXXXX, KC_LSFT, KC_RSFT, KC_PAUSE,KC_F10, KC_F11, KC_F12, KC_NO, KC_UP, KC_FN1, KC_FN0 }, + {KC_NO, XXXXXXX, KC_NO, KC_LALT, _______, XXXXXXX, XXXXXXX, _______, XXXXXXX, KC_DOWN, KC_RIGHT,KC_NO } + }, +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // to First overlay + [1] = ACTION_LAYER_MOMENTARY(2), // to Second overlay + +};
\ No newline at end of file diff --git a/keyboards/handwired/minorca/keymaps/default/readme.md b/keyboards/handwired/minorca/keymaps/default/readme.md new file mode 100644 index 0000000000..6ed31f82b3 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/default/readme.md @@ -0,0 +1,5 @@ +# The Default Minorca Layout + +Copied from https://github.com/pancinteractive/qmk_firmware/blob/master/keyboard/minorca_mkV/keymaps/default/keymap.c + +It looks incomplete.
\ No newline at end of file diff --git a/keyboards/handwired/minorca/keymaps/readme.md b/keyboards/handwired/minorca/keymaps/readme.md new file mode 100644 index 0000000000..058923ba25 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/readme.md @@ -0,0 +1,23 @@ +# How to add your own keymap + +Folders can be named however you'd like (will be approved upon merging), or should follow the format with a preceding `_`: + + _[ISO 3166-1 alpha-2 code*]_[layout variant]_[layout name/author] + +\* See full list: https://en.wikipedia.org/wiki/ISO_3166-1#Officially_assigned_code_elements + +and contain the following files: + +* `keymap.c` +* `readme.md` *recommended* +* `config.h` *optional*, found automatically when compiling +* `Makefile` *optional*, found automatically when compling + +When adding your keymap to this list, keep it organised alphabetically (select list, edit->sort lines), and use this format: + + * **folder_name** description + +# List of Minorca keymaps + +* **default** default Minorca layout +* **rgb** layout with WS2812b control diff --git a/keyboards/handwired/minorca/keymaps/rgb/Makefile b/keyboards/handwired/minorca/keymaps/rgb/Makefile new file mode 100644 index 0000000000..2b2af13358 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change to "no" to disable the options, or define them in the Makefile in +# the appropriate keymap folder that will get included automatically +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = yes # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../../Makefile +endif diff --git a/keyboards/handwired/minorca/keymaps/rgb/config.h b/keyboards/handwired/minorca/keymaps/rgb/config.h new file mode 100644 index 0000000000..deaac2e26f --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/config.h @@ -0,0 +1,20 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +/* bootmagic salt key */ +#define BOOTMAGIC_KEY_SALT KC_ESC + +/* skip bootmagic and eeconfig */ +#define BOOTMAGIC_KEY_SKIP KC_SPACE + +/* ws2812 RGB LED */ +#define RGB_DI_PIN D5 +#define RGBLIGHT_TIMER +#define RGBLED_NUM 13 // Number of LEDs +#define RGBLIGHT_HUE_STEP 10 +#define RGBLIGHT_SAT_STEP 17 +#define RGBLIGHT_VAL_STEP 17 + +#endif diff --git a/keyboards/handwired/minorca/keymaps/rgb/example.jpg b/keyboards/handwired/minorca/keymaps/rgb/example.jpg Binary files differnew file mode 100644 index 0000000000..a04c8d37d6 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/example.jpg diff --git a/keyboards/handwired/minorca/keymaps/rgb/keymap.c b/keyboards/handwired/minorca/keymaps/rgb/keymap.c new file mode 100644 index 0000000000..9002afbb88 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/keymap.c @@ -0,0 +1,65 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "minorca.h" +#include "action_layer.h" +#include "eeconfig.h" + +extern keymap_config_t keymap_config; + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _LOWER 1 +#define _RAISE 2 +#define _TB 3 + +// Macro name shortcuts +#define QWERTY M(_QWERTY) +#define LOWER M(_LOWER) +#define RAISE M(_RAISE) + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +[_QWERTY] = { /* Qwerty */ + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC}, + {FUNC(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, XXXXXXX, KC_QUOT}, + {KC_LSFT, XXXXXXX, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, FUNC(1)}, + {KC_LCTL, XXXXXXX, KC_LGUI, KC_LALT, FUNC(2), XXXXXXX, XXXXXXX, FUNC(3), XXXXXXX, KC_RALT, KC_APP, KC_RCTL} +}, + +[_RAISE] = { + {S(KC_GRV), S(KC_1), S(KC_2), S(KC_3), S(KC_4), S(KC_5), S(KC_6), S(KC_7), S(KC_8), S(KC_9), S(KC_0), KC_BSPC}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_PAUSE, KC_TRNS, KC_TRNS, KC_TRNS, S(KC_MINS), S(KC_EQL), S(KC_LBRC), XXXXXXX, S(KC_BSLS)}, + {KC_TRNS, XXXXXXX, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_ENT}, + {KC_TRNS, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_MNXT, KC_MUTE, KC_MPLY} +}, + +[_LOWER] = { + {KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_DELETE}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MINS, KC_EQL, KC_LBRC, XXXXXXX, KC_BSLS}, + {KC_TRNS, XXXXXXX, KC_F11, KC_F12, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_PGUP, KC_ENT}, + {KC_TRNS, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_HOME, KC_PGDN, KC_END} +}, + +[_TB] = { /* Tab */ + {KC_ESC, KC_CALC, KC_WHOM, KC_MAIL, KC_MYCM, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_TRNS}, + {KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, KC_TRNS}, + {KC_TRNS, XXXXXXX, RGB_TOG, RGB_MOD, RGB_HUI, RGB_HUD, RGB_SAI, RGB_SAD, RGB_VAI, RGB_VAD, KC_UP, KC_ENT}, + {BL_STEP, XXXXXXX, KC_TRNS, KC_TRNS, KC_TRNS, XXXXXXX, XXXXXXX, KC_TRNS, XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT} +} +}; + + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_KEY(_TB, KC_TAB), + [1] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_ENT), + [2] = ACTION_LAYER_TAP_KEY(_RAISE, KC_SPC), + [3] = ACTION_LAYER_TAP_KEY(_LOWER, KC_SPC), +}; diff --git a/keyboards/handwired/minorca/keymaps/rgb/readme.md b/keyboards/handwired/minorca/keymaps/rgb/readme.md new file mode 100644 index 0000000000..f50dfa546f --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/readme.md @@ -0,0 +1,25 @@ +#RGB backlight for MinOrca + + + +Example of adding WS2812b LEDs to a MinOrca. + +http://www.40percent.club/2016/08/tiny-whale.html + +The keymap is a work in progress. The RGB functions are accessed by holding down the TAB key. + +* Tab + Z Toggle on/off +* Tab + X Mode +* Tab + C Hue+ +* Tab + V Hue- +* Tab + B Saturation+ +* Tab + N Saturation- +* Tab + M Brightness+ +* Tab + , Brightness- + +Example wiring: + +WS2812 data pin is connected to D5 + + + diff --git a/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg b/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg Binary files differnew file mode 100644 index 0000000000..7dcbe80c5e --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/wiring1.jpg diff --git a/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg b/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg Binary files differnew file mode 100644 index 0000000000..fd91d3e1c9 --- /dev/null +++ b/keyboards/handwired/minorca/keymaps/rgb/wiring2.jpg diff --git a/keyboards/handwired/minorca/minorca.c b/keyboards/handwired/minorca/minorca.c new file mode 100644 index 0000000000..24e72c2a5c --- /dev/null +++ b/keyboards/handwired/minorca/minorca.c @@ -0,0 +1,6 @@ +#include "minorca.h" + +void matrix_init_kb(void) { + + matrix_init_user(); +}
\ No newline at end of file diff --git a/keyboards/handwired/minorca/minorca.h b/keyboards/handwired/minorca/minorca.h new file mode 100644 index 0000000000..158e5b4c55 --- /dev/null +++ b/keyboards/handwired/minorca/minorca.h @@ -0,0 +1,6 @@ +#ifndef MINORCA_H +#define MINORCA_H + +#include "quantum.h" + +#endif diff --git a/keyboards/handwired/minorca/readme.md b/keyboards/handwired/minorca/readme.md new file mode 100644 index 0000000000..93c767954d --- /dev/null +++ b/keyboards/handwired/minorca/readme.md @@ -0,0 +1,33 @@ +minorca keyboard firmware +====================== +Handwired 40% keyboard + +http://www.panc.co/blog/minorcasebright-information-page + +## Quantum MK Firmware + +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building + +Download or clone the whole firmware and navigate to the keyboards/planck folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use `make dfu` to program your PCB once you hit the reset button. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. + +### Notable forks (which some of the keymap files are from) +- [Shane's Fork](https://github.com/shanecelis/tmk_keyboard/tree/master/keyboard/planck) +- [Pierre's Fork](https://github.com/pcarrier/tmk_keyboard/blob/pcarrier/planck/keyboard/gh60/keymap_planck.c) +- [Nathan's Fork](https://github.com/nathanrosspowell/tmk_keyboard/tree/planck-jack/keyboard/planck) +- [Matthew's Fork](https://github.com/pepers/tmk_keyboard/tree/master/keyboard/planck_grid) diff --git a/keyboards/preonic/keymaps/jacwib/Makefile b/keyboards/preonic/keymaps/jacwib/Makefile new file mode 100644 index 0000000000..3e87d41d36 --- /dev/null +++ b/keyboards/preonic/keymaps/jacwib/Makefile @@ -0,0 +1,20 @@ + + +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = yes # Audio output on port C6 +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID +RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time. + +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/preonic/keymaps/jacwib/config.h b/keyboards/preonic/keymaps/jacwib/config.h new file mode 100644 index 0000000000..23e9e0ed28 --- /dev/null +++ b/keyboards/preonic/keymaps/jacwib/config.h @@ -0,0 +1,8 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +#define FORCE_NKRO 1 + +#endif diff --git a/keyboards/preonic/keymaps/jacwib/keymap.c b/keyboards/preonic/keymaps/jacwib/keymap.c new file mode 100644 index 0000000000..cf441bf309 --- /dev/null +++ b/keyboards/preonic/keymaps/jacwib/keymap.c @@ -0,0 +1,215 @@ +#include "preonic.h" +#include "action_layer.h" +#include "eeconfig.h" +#include "keymap_nordic.h" +#ifdef AUDIO_ENABLE + #include "audio.h" +#endif + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _QWERTY 0 +#define _LOWER 3 +#define _RAISE 4 +#define _ADJUST 16 + +enum preonic_keycodes { + QWERTY = SAFE_RANGE, + LOWER, + RAISE, + BACKLIT +}; + +// Fillers to make layering more clear +#define _______ KC_TRNS +#define XXXXXXX KC_NO + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +/* Qwerty + * ,-----------------------------------------------------------------------------------. + * | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | + | Bksp | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Esc | Q | W | E | R | T | Y | U | I | O | P | Å | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | Tab | A | S | D | F | G | H | J | K | L | Ö | Ä | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | Shift| < | Z | X | C | V | B | N | M | . | , | - | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | Ctrl | GUI | Alt |AltGr |Lower | Space| Enter|Raise | Left | Down | Up |Right | + * `-----------------------------------------------------------------------------------' + */ +[_QWERTY] = { + {KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, NO_PLUS, KC_BSPC}, + {KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, NO_AM }, + {KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, NO_AE, NO_OSLH}, + {KC_LSFT, NO_LESS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_DOT, KC_COMM, NO_MINS}, + {KC_LCTL, KC_LGUI, KC_LALT, NO_ALGR, LOWER, KC_SPC, KC_ENT, RAISE, KC_LEFT, KC_DOWN, KC_UP, KC_RGHT} +}, + +/* Lower + * ,-----------------------------------------------------------------------------------. + * | | @ | £ | $ | | | { | [ | ] | } | \ | Del | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | | | |VolUp | | | ~ | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | | |LastS |PauseP|NextS | | * | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | | | | | | | | |VolDwn| | | | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | |Bspc | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_LOWER] = { + {_______, NO_AT, NO_PND, NO_DLR, _______, _______, NO_LCBR, NO_LBRC, NO_RBRC, NO_RCBR, NO_BSLS, KC_DEL}, + {_______, _______, _______, _______, _______, _______, _______, _______, KC_VOLU, _______, _______, NO_TILD}, + {_______, _______, _______, _______, _______, _______, _______, KC_MPRV, KC_MPLY, KC_MNXT, _______, LSFT(KC_BSLS)}, + {_______, NO_PIPE, _______, _______, _______, _______, _______, _______, KC_VOLD, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, KC_BSPC, _______, _______, _______, _______, _______} +}, + +/* Raise + * ,-----------------------------------------------------------------------------------. + * | ! | " | # | ¤ | % | & | / | ( | ) | = | ? | Ins | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | |Mouse^| | | | |ScrlUp| | | ^ | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | |Mouse<|MouseV|Mouse>| | |MLC |MMC |MRC | ' | " | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | | > | | | | | | |ScrlDown| : | ; | _ | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | |Bspc | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_RAISE] = { + {LSFT(KC_1),NO_QUO2,LSFT(KC_3), NO_BULT,LSFT(KC_5), NO_AMPR, NO_SLSH, NO_LPRN, NO_RPRN, NO_EQL, NO_QUES, KC_INS}, + {_______, _______, _______, KC_MS_U, _______, _______, _______, _______, KC_WH_U, _______, _______, NO_CIRC}, + {_______, _______, KC_MS_L, KC_MS_D, KC_MS_R, _______, _______, KC_BTN1, KC_BTN3, KC_BTN2, NO_APOS, NO_QUOT}, + {_______, NO_GRTR, _______, _______, _______, _______, _______, _______, KC_WH_D, NO_COLN, NO_SCLN, NO_UNDS}, + {_______, _______, _______, _______, _______, KC_BSPC, _______, _______, _______, _______, _______, _______} +}, + +/* Adjust (Lower + Raise) + * ,-----------------------------------------------------------------------------------. + * | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | Reset| | | | | | | | | + * |------+------+------+------+------+-------------+------+------+------+------+------| + * | | | | | | | | | | | |Rsft | + * |------+------+------+------+------+------|------+------+------+------+------+------| + * | |MusOn |MusOff| | | | | | | | | Reset| + * |------+------+------+------+------+------+------+------+------+------+------+------| + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------' + */ +[_ADJUST] = { + {KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12}, + {_______, _______, _______, RESET, _______, _______, _______, _______, _______, _______, _______, _______}, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, KC_RSFT}, + {_______, MU_ON, MU_OFF, _______, _______, _______, _______, _______, _______, _______, _______, RESET }, + {_______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______} +} + + +}; + +#ifdef AUDIO_ENABLE +float tone_startup[][2] = { + {NOTE_B5, 20}, + {NOTE_B6, 8}, + {NOTE_DS6, 20}, + {NOTE_B6, 8} +}; + +float tone_qwerty[][2] = SONG(QWERTY_SOUND); + +float tone_goodbye[][2] = SONG(GOODBYE_SOUND); + +float music_scale[][2] = SONG(MUSIC_SCALE_SOUND); +#endif + +void persistant_default_layer_set(uint16_t default_layer) { + eeconfig_update_default_layer(default_layer); + default_layer_set(default_layer); +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + switch (keycode) { + case QWERTY: + if (record->event.pressed) { + #ifdef AUDIO_ENABLE + PLAY_NOTE_ARRAY(tone_qwerty, false, 0); + #endif + persistant_default_layer_set(1UL<<_QWERTY); + } + return false; + break; + case LOWER: + if (record->event.pressed) { + layer_on(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_LOWER); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case RAISE: + if (record->event.pressed) { + layer_on(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } else { + layer_off(_RAISE); + update_tri_layer(_LOWER, _RAISE, _ADJUST); + } + return false; + break; + case BACKLIT: + if (record->event.pressed) { + register_code(KC_RSFT); + #ifdef BACKLIGHT_ENABLE + backlight_step(); + #endif + } else { + unregister_code(KC_RSFT); + } + return false; + break; + } + return true; +}; + +void matrix_init_user(void) { + #ifdef AUDIO_ENABLE + startup_user(); + #endif +} + +#ifdef AUDIO_ENABLE + +void startup_user() +{ + _delay_ms(20); // gets rid of tick + PLAY_NOTE_ARRAY(tone_startup, false, 0); +} + +void shutdown_user() +{ + PLAY_NOTE_ARRAY(tone_goodbye, false, 0); + _delay_ms(150); + stop_all_notes(); +} + +void music_on_user(void) +{ + music_scale_user(); +} + +void music_scale_user(void) +{ + PLAY_NOTE_ARRAY(music_scale, false, 0); +} + +#endif diff --git a/keyboards/preonic/keymaps/jacwib/readme.md b/keyboards/preonic/keymaps/jacwib/readme.md new file mode 100644 index 0000000000..0660312353 --- /dev/null +++ b/keyboards/preonic/keymaps/jacwib/readme.md @@ -0,0 +1,3 @@ +# Jacwib's preonic keymap. + +Designed for use with a swedish language. |
