summaryrefslogtreecommitdiff
path: root/keyboards
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards')
-rw-r--r--keyboards/handwired/CMD60/CMD60.c8
-rw-r--r--keyboards/handwired/CMD60/CMD60.h20
-rw-r--r--keyboards/handwired/CMD60/Makefile73
-rw-r--r--keyboards/handwired/CMD60/README.md35
-rw-r--r--keyboards/handwired/CMD60/config.h162
-rw-r--r--keyboards/handwired/CMD60/keymaps/default/keymap.c66
6 files changed, 364 insertions, 0 deletions
diff --git a/keyboards/handwired/CMD60/CMD60.c b/keyboards/handwired/CMD60/CMD60.c
new file mode 100644
index 0000000000..799848e34e
--- /dev/null
+++ b/keyboards/handwired/CMD60/CMD60.c
@@ -0,0 +1,8 @@
+#include "CMD60.h"
+
+void matrix_init_kb(void) {
+ // put your keyboard start-up code here
+ // runs once when the firmware starts up
+
+ matrix_init_user();
+}
diff --git a/keyboards/handwired/CMD60/CMD60.h b/keyboards/handwired/CMD60/CMD60.h
new file mode 100644
index 0000000000..f90871fc71
--- /dev/null
+++ b/keyboards/handwired/CMD60/CMD60.h
@@ -0,0 +1,20 @@
+#ifndef CMD60_H
+#define CMD60_H
+
+#include "quantum.h"
+
+#define KEYMAP( \
+ K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \
+ K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \
+ K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \
+ K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \
+ K40, K41, K42, K45, K4A, K4B, K4C, K4D \
+ ) { \
+ { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \
+ { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \
+ { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D }, \
+ { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \
+ { K40, K41, K42, KC_NO, KC_NO, K45, KC_NO, KC_NO, KC_NO, KC_NO,K4A, K4B, K4C, K4D } \
+}
+
+#endif \ No newline at end of file
diff --git a/keyboards/handwired/CMD60/Makefile b/keyboards/handwired/CMD60/Makefile
new file mode 100644
index 0000000000..7117599173
--- /dev/null
+++ b/keyboards/handwired/CMD60/Makefile
@@ -0,0 +1,73 @@
+
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in *bytes*
+# Teensy halfKay 512
+# Teensy++ halfKay 1024
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+# USBaspLoader 2048
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+# change yes to no to disable
+#
+BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
+CONSOLE_ENABLE ?= yes # Console for debug(+400)
+COMMAND_ENABLE ?= yes # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE ?= no # USB Nkey Rollover
+BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default
+MIDI_ENABLE ?= no # MIDI controls
+UNICODE_ENABLE ?= no # Unicode
+BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE ?= no # Audio output on port C6
+
+ifndef QUANTUM_DIR
+ include ../../../Makefile
+endif
+
+
diff --git a/keyboards/handwired/CMD60/README.md b/keyboards/handwired/CMD60/README.md
new file mode 100644
index 0000000000..83e371543e
--- /dev/null
+++ b/keyboards/handwired/CMD60/README.md
@@ -0,0 +1,35 @@
+CMD60 keyboard firmware
+======================
+
+##CMD60
+
+This layout has been designed to optimize use of the left-hand, and it focussed specifically on programmers who work
+with text editors like SublimeText and Atom. It utilizes the power of Space_fn, and features a caps lock swap for Fn2
+and enter key on tap. These features allow you to keep your right hand on the mouse more and should enable you to
+achieve a higher level of productivity if you take the time to learn its function layers.
+
+## Quantum MK Firmware
+
+For the full Quantum feature list, see [the parent readme.md](/doc/readme.md).
+
+## Building
+
+Download or clone the whole firmware and navigate to the keyboards/handwired/CMD60 folder.
+Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use
+the Teensy Loader to program your .hex file.
+
+Depending on which keymap you would like to use, you will have to compile slightly differently.
+
+### Default
+
+To build with the default keymap, simply run `make`.
+
+### Other Keymaps
+
+To build the firmware binary hex file with a keymap just do `make` with `keymap` option like:
+
+```
+$ make keymap=[default|jack|<name>]
+```
+
+Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/`
diff --git a/keyboards/handwired/CMD60/config.h b/keyboards/handwired/CMD60/config.h
new file mode 100644
index 0000000000..27eb400b87
--- /dev/null
+++ b/keyboards/handwired/CMD60/config.h
@@ -0,0 +1,162 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x6060
+#define DEVICE_VER 0x0001
+#define MANUFACTURER cmd
+#define PRODUCT CMD60
+#define DESCRIPTION Advanced Programming Keeb Layout
+
+/* key matrix size */
+#define MATRIX_ROWS 5
+#define MATRIX_COLS 14
+
+/*
+ * Keyboard Matrix Assignments
+ *
+ * Change this to how you wired your keyboard
+ * COLS: AVR pins used for columns, left to right
+ * ROWS: AVR pins used for rows, top to bottom
+ * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode)
+ * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode)
+ *
+*/
+#define MATRIX_ROW_PINS { F0, F4, F5, F6, F7 }
+#define MATRIX_COL_PINS { B0, B1, B2, B3, B7, D0, D1, D2, D3, C6, D7, B4, B5, B6 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+// #define BACKLIGHT_PIN B7
+// #define BACKLIGHT_BREATHING
+// #define BACKLIGHT_LEVELS 3
+
+
+/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
+#define DEBOUNCING_DELAY 5
+
+/* define if matrix has ghost (lacks anti-ghosting diodes) */
+//#define MATRIX_HAS_GHOST
+
+/* number of backlight levels */
+
+/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
+#define LOCKING_SUPPORT_ENABLE
+/* Locking resynchronize hack */
+#define LOCKING_RESYNC_ENABLE
+
+/*
+ * Force NKRO
+ *
+ * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
+ * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
+ * makefile for this to work.)
+ *
+ * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
+ * until the next keyboard reset.
+ *
+ * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
+ * fully operational during normal computer usage.
+ *
+ * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
+ * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
+ * bootmagic, NKRO mode will always be enabled until it is toggled again during a
+ * power-up.
+ *
+ */
+//#define FORCE_NKRO
+
+/*
+ * Magic Key Options
+ *
+ * Magic keys are hotkey commands that allow control over firmware functions of
+ * the keyboard. They are best used in combination with the HID Listen program,
+ * found here: https://www.pjrc.com/teensy/hid_listen.html
+ *
+ * The options below allow the magic key functionality to be changed. This is
+ * useful if your keyboard/keypad is missing keys and you want magic key support.
+ *
+ */
+
+/* key combination for magic key command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* control how magic key switches layers */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false
+
+/* override magic key keymap */
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS
+//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM
+//#define MAGIC_KEY_HELP1 H
+//#define MAGIC_KEY_HELP2 SLASH
+//#define MAGIC_KEY_DEBUG D
+//#define MAGIC_KEY_DEBUG_MATRIX X
+//#define MAGIC_KEY_DEBUG_KBD K
+//#define MAGIC_KEY_DEBUG_MOUSE M
+//#define MAGIC_KEY_VERSION V
+//#define MAGIC_KEY_STATUS S
+//#define MAGIC_KEY_CONSOLE C
+//#define MAGIC_KEY_LAYER0_ALT1 ESC
+//#define MAGIC_KEY_LAYER0_ALT2 GRAVE
+//#define MAGIC_KEY_LAYER0 0
+//#define MAGIC_KEY_LAYER1 1
+//#define MAGIC_KEY_LAYER2 2
+//#define MAGIC_KEY_LAYER3 3
+//#define MAGIC_KEY_LAYER4 4
+//#define MAGIC_KEY_LAYER5 5
+//#define MAGIC_KEY_LAYER6 6
+//#define MAGIC_KEY_LAYER7 7
+//#define MAGIC_KEY_LAYER8 8
+//#define MAGIC_KEY_LAYER9 9
+//#define MAGIC_KEY_BOOTLOADER PAUSE
+//#define MAGIC_KEY_LOCK CAPS
+//#define MAGIC_KEY_EEPROM E
+//#define MAGIC_KEY_NKRO N
+//#define MAGIC_KEY_SLEEP_LED Z
+
+/*
+ * Feature disable options
+ * These options are also useful to firmware size reduction.
+ */
+
+/* disable debug print */
+//#define NO_DEBUG
+
+/* disable print */
+//#define NO_PRINT
+
+/* disable action features */
+//#define NO_ACTION_LAYER
+//#define NO_ACTION_TAPPING
+//#define NO_ACTION_ONESHOT
+//#define NO_ACTION_MACRO
+//#define NO_ACTION_FUNCTION
+
+#endif
diff --git a/keyboards/handwired/CMD60/keymaps/default/keymap.c b/keyboards/handwired/CMD60/keymaps/default/keymap.c
new file mode 100644
index 0000000000..9f9cbcd661
--- /dev/null
+++ b/keyboards/handwired/CMD60/keymaps/default/keymap.c
@@ -0,0 +1,66 @@
+#include "CMD60.h"
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+ [0] = KEYMAP( /* CMD60 - QWERTY */
+ KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \
+ LT(3, KC_ENT), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_NO, KC_RSFT, \
+ KC_LCTL, KC_LGUI, KC_LALT, LT(2, KC_SPC), MO(3), MO(4), MO(5), TG(1) \
+ ),
+ [1] = KEYMAP( /* CMD60 - GameMode */
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_CAPS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, \
+ KC_LSFT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_RSFT, \
+ KC_TRNS, KC_NO, KC_TRNS, KC_SPC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \
+ ),
+ [2] = KEYMAP( /* CMD60 - Arrows */
+ KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \
+ KC_TRNS, KC_BSPC, KC_UP, KC_DEL, KC_TRNS, KC_TRNS, KC_TRNS, KC_BSPC, KC_UP, KC_DEL, KC_PSCR, KC_SLCK, KC_PAUS, KC_TRNS, \
+ KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_SPC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \
+ ),
+ [3] = KEYMAP( /* CMD60 - Functions */
+ KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \
+ KC_AUDIO_MUTE, KC_BSPC, KC_PGUP, KC_DEL, KC_TRNS, KC_TRNS, KC_TRNS, KC_PGUP, KC_UP, KC_PGDN, KC_TRNS, KC_PAUSE, KC_SLCK, KC_PSCREEN, \
+ KC_TRNS, KC_HOME, KC_PGDN, KC_END, KC_TRNS, KC_TRNS, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_INSERT, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_END, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \
+ ),
+ [4] = KEYMAP( /* CMD60 - Mouse */
+ KC_SYSTEM_SLEEP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_BTN1, KC_MS_UP, KC_MS_BTN2, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_LEFT, KC_MS_DOWN, KC_MS_RIGHT, KC_TRNS, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MS_WH_UP, KC_MS_BTN3, KC_MS_WH_DOWN, KC_NO, KC_NO, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \
+ ),
+ [5] = KEYMAP( /* CMD60 - Media */
+ KC_SYSTEM_WAKE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_AUDIO_VOL_DOWN, KC_AUDIO_VOL_UP, KC_AUDIO_MUTE, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_MEDIA_PREV_TRACK, KC_MEDIA_NEXT_TRACK, KC_MEDIA_PLAY_PAUSE, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_WWW_BACK, KC_WWW_FORWARD, KC_NO, KC_NO, KC_WWW_REFRESH, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \
+ ),
+};
+
+const uint16_t PROGMEM fn_actions[] = {
+
+};
+
+
+const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt)
+{
+ // MACRODOWN only works in this function
+ switch(id) {
+ case 0:
+ if (record->event.pressed) {
+ register_code(KC_RSFT);
+ } else {
+ unregister_code(KC_RSFT);
+ }
+ break;
+ }
+ return MACRO_NONE;
+};
generated by cgit v1.2.1 (git 2.18.0) at 2024-11-30 14:54:28 +0000