From e337bb82a3b418dfd6c60b8c615322c854e5995d Mon Sep 17 00:00:00 2001
From: noroadsleft <18669334+noroadsleft@users.noreply.github.com>
Date: Mon, 29 Apr 2019 11:04:56 -0700
Subject: Fix Planck and Preonic builds (#5658)

* Planck: Copy contents of Planck rules.mk to each revision

* Planck: Delete Planck rules.mk

* Planck: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Preonic: Copy contents of Preonic rules.mk to each revision

* Preonic: Delete Preonic rules.mk

* Preonic: Concatenate duplicate rules

Concatenate rules that are set and then overridden into one setting.

* Planck: Delete non-specific Bootloader settings from revs. 1 and 2

Deleted BOOTLOADER setting code block, as the checks were only valid for revs. 3-5 and the Planck Light.

Neither Planck rev1 or rev2 set the bootloader via rules.mk, so there's no setting of BOOTLOADER in their rules.mk files.

* Preonic: Fix BOOTLOADER settings code blocks

* Preonic: delete extra blank lines from rules.mk files

* Preonic: delete AVR-type hardware config blocks from rev3

* Update Planck and Preonic readme files

- update Hardware Supported
- update/add Install Examples
- update Docs paragraph

* Enable Bootmagic Lite where it is disabled

Enabled Bootmagic Lite for:

- Planck Light
- Planck revs. 1-5
- Preonic revs. 1 and 2

* Remove `planck_grid` from LAYOUTS rule for all Planck revisions

Community has landed on `ortho_4x12`, which is already set; `planck_grid` is redundant.
---
 keyboards/preonic/rules.mk | 74 ----------------------------------------------
 1 file changed, 74 deletions(-)
 delete mode 100644 keyboards/preonic/rules.mk

(limited to 'keyboards/preonic/rules.mk')

diff --git a/keyboards/preonic/rules.mk b/keyboards/preonic/rules.mk
deleted file mode 100644
index e646f2493f..0000000000
--- a/keyboards/preonic/rules.mk
+++ /dev/null
@@ -1,74 +0,0 @@
-
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-#     This will define a symbol, F_CPU, in all source code files equal to the
-#     processor frequency in Hz. You can then use this symbol in your source code to
-#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-#     automatically to create a 32-bit value in your source code.
-#
-#     This will be an integer division of F_USB below, as it is sourced by
-#     F_USB after it has run through any CPU prescalers. Note that this value
-#     does not *change* the processor frequency - it should merely be updated to
-#     reflect the processor speed set externally so that the code can use accurate
-#     software delays.
-F_CPU = 16000000
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-#     This will define a symbol, F_USB, in all source code files equal to the
-#     input clock frequency (before any prescaling is performed) in Hz. This value may
-#     differ from F_CPU if prescaling is used on the latter, and is required as the
-#     raw input clock is fed directly to the PLL sections of the AVR for high speed
-#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-#     at the end, this will be done automatically to create a 32-bit value in your
-#     source code.
-#
-#     If no clock division is performed on the input clock inside the AVR (via the
-#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Bootloader
-#     This definition is optional, and if your keyboard supports multiple bootloaders of
-#     different sizes, comment this out, and the correct address will be loaded 
-#     automatically (+60). See bootloader.mk for all options.
-ifeq ($(strip $(KEYBOARD)), preonic/rev1)
-    BOOTLOADER = atmel-dfu
-endif
-ifeq ($(strip $(KEYBOARD)), preonic/rev2)
-    BOOTLOADER = qmk-dfu
-endif
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-# Build Options
-#   change to "no" to disable the options, or define them in the Makefile in 
-#   the appropriate keymap folder that will get included automatically
-#
-BOOTMAGIC_ENABLE = no       # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = no       # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes       # Audio control and System control(+450)
-CONSOLE_ENABLE = yes         # Console for debug(+400)
-COMMAND_ENABLE = no        # Commands for debug and configuration
-NKRO_ENABLE = no            # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-BACKLIGHT_ENABLE = yes      # Enable keyboard backlight functionality
-MIDI_ENABLE = no            # MIDI controls
-AUDIO_ENABLE = yes           # Audio output on port C6
-UNICODE_ENABLE = no         # Unicode
-BLUETOOTH_ENABLE = no       # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = no        # Enable WS2812 RGB underlight.
-API_SYSEX_ENABLE = no
-
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-SLEEP_LED_ENABLE = no    # Breathing sleep LED during USB suspend
-
-LAYOUTS = ortho_5x12
-- 
cgit v1.2.1