From 5b644af4155d2eae0005ed11f604f7b14dfa7456 Mon Sep 17 00:00:00 2001 From: Drashna Jaelre Date: Fri, 1 Oct 2021 19:11:34 -0700 Subject: [Keyboard] Enable Proton C defaults for SplitKB Kyria (#14490) Co-authored-by: Ryan --- keyboards/splitkb/kyria/readme.md | 22 +++++++++++++++++++++- 1 file changed, 21 insertions(+), 1 deletion(-) (limited to 'keyboards/splitkb/kyria/readme.md') diff --git a/keyboards/splitkb/kyria/readme.md b/keyboards/splitkb/kyria/readme.md index 5ce652589c..7ecf3946f7 100644 --- a/keyboards/splitkb/kyria/readme.md +++ b/keyboards/splitkb/kyria/readme.md @@ -10,7 +10,8 @@ Hardware Availability: [splitkb.com](https://splitkb.com) and partners. Make example for this keyboard (after setting up your build environment): - make splitkb/kyria:default + make splitkb/kyria/rev1:default + make splitkb/kyria/rev1/proton_c:default Example of flashing this keyboard: @@ -19,3 +20,22 @@ Example of flashing this keyboard: See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). A build guide for the Kyria can be found at [docs.splitkb.com](https://docs.splitkb.com/hc/en-us/articles/360010552059-Kyria-Build-Guide-Introduction). + +## Proton C Conversion Guide + +If you're one of the lucky people to have Proton Cs to use with their Kyria, there are a couple of caveats to getting this working. + +1. You need to have 2x Proton Cs, as you cannot mix and match with Pro Micros or Elite C's. They both need to be Proton Cs. +2. You'll need to do some modding to enable proper support with the Proton C. + +By design, the Kyria uses every available pin on the Pro Micro footprint. This includes using D3 (RX) for RGB. This poses a challenge with using the Proton C, since it needs both the TX and RX pins. The Proton C needs both pins, especially if you plan on using Full Duplex Serial. + +To fix this, you need to break off the last header position on the right-hand side on the footprint. This is the `TX0/D3` pad. Leave this pad without a header connected to. + +From the A9 pin on the Proton C, you want to run a wire from it to the `SDA + Extra Data` pad near the TRRS jack on the PCB. This will allow for proper, full duplex communication over the TRRS cable. + +To get RGB working properly, as well, you want to run a wire from the `A3` pin on the Proton C, next to the GND and DFU pin, right under the USB port. Run this to the `TX0/D3` pad (the one you left without a header pin on the PCB). + +Once you've done that, you can solder in the Proton C. and flash it. + +![Proton C](https://i.imgur.com/nICqWLo.jpg) -- cgit v1.2.1 From 14fb3cc8b04d019b585b0ea25d11f2939949429f Mon Sep 17 00:00:00 2001 From: "L. K. Post" Date: Mon, 21 Feb 2022 07:33:00 +0100 Subject: [Keyboard] Add Kyria rev. 2 (#16178) --- keyboards/splitkb/kyria/readme.md | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-) (limited to 'keyboards/splitkb/kyria/readme.md') diff --git a/keyboards/splitkb/kyria/readme.md b/keyboards/splitkb/kyria/readme.md index 7ecf3946f7..32e6ae5f8e 100644 --- a/keyboards/splitkb/kyria/readme.md +++ b/keyboards/splitkb/kyria/readme.md @@ -10,12 +10,16 @@ Hardware Availability: [splitkb.com](https://splitkb.com) and partners. Make example for this keyboard (after setting up your build environment): - make splitkb/kyria/rev1:default - make splitkb/kyria/rev1/proton_c:default + make splitkb/kyria/rev2:default + make splitkb/kyria/rev2/proton_c:default Example of flashing this keyboard: - make splitkb/kyria/rev1:default:flash + make splitkb/kyria/rev2:default:flash + +Replace "rev2" with "rev1" if you have a Kyria of revision 1.4 or below. +Not sure what revision yours is? It is printed on the outer lower edge of the PCB! +As a rule of thumb, all Kyrias sold after January 1st 2022 are revision 2.x. See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs). -- cgit v1.2.1